Riverbed 830-01 Online Practice Questions and Exam Preparation

Riverbed 830-01 Online Questions & Answers

• Question 201:

  Which of the following reports are available on the CMC appliance? (Select 4)

  A. Optimized Throughput
  B. Traffic Summary
  C. Current Connections
  D. Connection History
  E. Data Store Hit Rate
  A. Optimized Throughput
  B. Traffic Summary
  D. Connection History
  E. Data Store Hit Rate

• Question 202:

  What is required for the Embedded Cascade Shark function to work? (Select 3)

  A. TCP port 61898 should be open between the Steelhead and the remote Cascade Pilot.
  B. You must give the username Shark a password.
  C. You must enable Cascade Shark on the Management Console TCP Dumps menu.
  D. The optimization service needs to be restarted.
  A. TCP port 61898 should be open between the Steelhead and the remote Cascade Pilot.
  B. You must give the username Shark a password.
  C. You must enable Cascade Shark on the Management Console TCP Dumps menu.

• Question 203:

  What action is taken by the Interceptor if a connection does not match a configured load balance rule and the default pool is empty?

  A. The connection is forwarded for auto-discovery.
  B. The connection is passed-through.
  C. The connection is rejected.
  D. The connection is reset.
  B. The connection is passed-through.

• Question 204:

  What is the default Load Balancing rule on an Interceptor appliance?

  A. Redirect
  B. Allow
  C. Auto
  D. Pass-through
  C. Auto

• Question 205:

  What type of reporting information will an Interceptor appliance store? (Select 2)

  A. Connection counts
  B. Total packets in and out
  C. Bytes and packets redirected to each neighbor Steelhead appliance
  D. Scalable Data Referencing (SDR) Status
  A. Connection counts
  B. Total packets in and out

• Question 206:

  You can monitor your Steelhead appliance disk performance using which reports? (Select 2)

  A. Data Store Cost
  B. Data Store Performance
  C. Disk Load
  D. SDR Hit
  E. Disk Pressure
  F. Disk Alarm
  A. Data Store Cost
  C. Disk Load

• Question 207:

  Which user roles and permissions are supported by the CMC appliance? (Select 3)

  A. Read-Only
  B. Read/Write
  C. Write-Only
  D. Deny
  E. Accept
  A. Read-Only
  B. Read/Write
  D. Deny

• Question 208:

  In a new physical in-path deployment, you realize that a Steelhead appliance at one of your branch offices is optimizing connections from other sites, however, no connections initiated from that branch office are being optimized. Which of the following is the most likely cause of this problem?

  A. Duplex mismatch
  B. Bilateral Opportunistic Lock failure
  C. Policy-based routing incorrectly configured
  D. Reversed WAN and LAN cabling
  D. Reversed WAN and LAN cabling

• Question 209:

  A SteelHead is deployed on an 802.1Q trunk in the diagram below. A connection is being optimized from a client on VLAN 20 using Correct Addressing. Which VLAN ID will be on the inner channel connection?

  

  A. 10
  B. 20
  C. The native VLAN
  D. No VLAN ID
  E. Only VLAN 10 can be optimized. All other are passed through on their original tag
  B. 20

• Question 210:

  Refer to the exhibit.

  

  A customer is reporting that the first connection from a user to the server is failing. However, subsequent connections work properly and are optimized. How can this problem best be resolved?

  A. Fixed-target rule
  B. Enable RIP/OSPF on the routers
  C. Enable Simplified Routing
  D. Enable QoS
  E. Enable RIP/OSPF on the Steelhead appliances
  C. Enable Simplified Routing