Microsoft 70-741 Online Practice Questions and Exam Preparation

Microsoft 70-741 Online Questions & Answers

• Question 241:

  Note: This question is part of a series of questions that use the same or similar answer choices. An answer choice may be correct for more than one question in the series. Each question is independent of the other questions in this series.

  Information and details provided in a question apply only to that question.

  You have a DHCP server named Server1 that has an IPv4 scope named Scope1.

  Users report that when they turn on their client computers, it takes a long time to access the network.

  You validate that it takes a long time for the computers to receive an IP address from Server1.

  You monitor the network traffic and discover that Server1 issues five ping commands on the network before leasing an IP address.

  You need to reduce the amount of time it takes for the computers to receive an IP address.

  What should you do?

  A. From the properties of Scope1, modify the Conflict detection attempts setting.
  B. From the properties of Scope1, configure Name Protection.
  C. From the properties of IPv4, configure the bindings.
  D. From IPv4, create a new filter.
  E. From the properties of Scope1, create an exclusion range.
  F. From IPv4, run the DHCP Policy Configuration Wizard.
  G. From Control Panel, modify the properties of Ethernet.
  H. From Scope1, create a reservation.
  A. From the properties of Scope1, modify the Conflict detection attempts setting.

• Question 242:

  HOTSPOT

  You are configuring internal virtual networks to support multitenancy communication between tenant virtual machine networks and remote sites.

  You have a tenant named Tenant1.

  You need to enable Border Gateway Protocol (BGP) for Tenant1.

  Which commands should you run? To answer, select the appropriate options in the answer area.

  NOTE: Each correct selection is worth one point.

  Hot Area:

  

  

• Question 243:

  You have a DNS server named DNS1 that hosts several forward lookup zones.

  You discover that dynamic records exist for computers that there were removed from your network several months ago.

  You need to ensure that the records are removed automatically.

  Which two actions should you perform? Each correct answer presents part of the solution.

  NOTE: Each correct selection is worth one point.

  A. From the Start of Authority (SOA) settings of each zone, configure the Retry interval setting and the Minimum (default) TTL setting.
  B. For each zone, set Dynamic updates to Secure only.
  C. From the Start of Authority (SOA) settings of each zone, configure the Refresh interval setting and the Expires after setting.
  D. For each zone, select Scavenge stale resource records.
  E. From the Advanced settings of the DNS server properties, select Enable automatic scavenging of state records.
  A. From the Start of Authority (SOA) settings of each zone, configure the Retry interval setting and the Minimum (default) TTL setting.
  C. From the Start of Authority (SOA) settings of each zone, configure the Refresh interval setting and the Expires after setting.

• Question 244:

  You have servers that run Windows Server 2016 and devices that run Windows 10 Enterprise.

  You have a certification authority (CA) that issued computer certificates to all the servers and devices.

  You plan to allow the Windows 10 devices to connect to the network remotely by using VPN device tunnels.

  You install the Remote Access server role on a server. From the Routing and Remote Access console, you configure the server for the VPN role.

  You need to ensure that the Windows 10 devices can establish the VPN tunnel before users sign in to the devices.

  What should you do on the VPN server?

  A. From Authentication Methods, select Allow machine certificate authentication for IKEv2.
  B. Modify the ports properties and add additional SSTP ports.
  C. From Authentication Methods, select Extensible authentication protocol (EAP).
  D. Modify the ports properties and add additional IKEv2 ports.
  A. From Authentication Methods, select Allow machine certificate authentication for IKEv2.

• Question 245:

  Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some question sets might have more than one correct solution, while

  others might not have a correct solution.

  After you answer a question in this sections, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.

  Your network contains an Active Directory domain named contoso.com

  You need to create a Nano Server image named Nano1 that will be used as a virtualization host. The windows server 2016 source files are located in drive D.

  Solution: You run the following cmdlet.

  Does this meet the goal?

  A. Yes
  B. NO
  B. NO

• Question 246:

  HOTSPOT

  Your network contains an Active Directory forest named contoso.com. The forest contains the VPN servers configured as shown in the following table.

  

  You are configuring a Network Policy Server (NPS) server named Server1. Server1 has the following RADIUS clients.

  

  All three VPN servers are configured to use Server1 for RADIUS authentication. All of the users in comtoso.com are allowed to establish a VPN connection. For each of the following statements, select YES if the statement is true. Otherwise, select No.

  NOTE: Each correct selection is worth one point.

  Hot Area:

  

  

• Question 247:

  Your company owns the public Internet IP address range of 131.107.20.0 to 131.107.20.255.

  You need to create a subnet that supports four hosts. The solution must minimize the number of addresses available to the subnet.

  Which subnet should you use?

  A. 131.107.20.16 with subnet mask 255.255.255.248
  B. 131.107.20.16/28
  C. 131.107.20.0/27
  D. 131.107.20.16/30
  A. 131.107.20.16 with subnet mask 255.255.255.248

• Question 248:

  HOTSPOT

  You use a Network Policy Server (NPS) server named NPS1 to authenticate VPN connections and connections to wireless access points (WAPs).

  You plan to add a new WAP named WAP1.

  What should you do on WAP1 and NPS1? To answer, select the appropriate options in the answer area.

  NOTE: Each correct selection is worth one point.

  Hot Area:

  

  

• Question 249:

  Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some questions sets might have more than one correct solutions,

  while others might not have a correct solution.

  After you answer a question in this section, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.

  You have a server named Server1 that runs Windows Server 2016. Server1 is configured as a VPN server.

  Server1 is configured to allow domain users to establish VPN connections from 06:00 to 18:00 everyday of the week.

  You need to ensure that domain users can establish VPN connections only between Monday and Friday.

  Solution: From Server Manager, You modify the Access Policies on Server1.

  Does this meet the goal?

  A. Yes
  B. No
  A. Yes

• Question 250:

  HOTSPOT

  Your network contains an Active Directory domain named contoso.com. The domain contains a DNS server named Server1.

  Server1 is configured to use a forwarder named server2.contoso.com that has an IP address of 10.0.0.10.

  You need to prevent Server1 from using root hints if the forwarder is unavailable.

  What command should you run? To answer, select the appropriate options in the answer area.

  Hot Area: