Avaya 6103 Online Practice Questions and Exam Preparation

Avaya 6103 Online Questions & Answers

• Question 41:

  Which function does the "RS" module for the ERS 8000 provide that the "R" module does not?

  A. multiple port mirroring
  B. multiple port cloning
  C. SMLT functionality
  D. extended port monitoring
  C. SMLT functionality

• Question 42:

  Which CLI command is used to validate that synchronization for High Availability mode is correct?

  A. show ha-info
  B. show ha-all
  C. show ha-state
  D. show ha-sync
  A. show ha-info

• Question 43:

  A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 switches, to a core pair of ERS 8000 switches. Which statement about the correct uplink configuration is true?

  A. Distribute uplinks across different ERS 5500 switches in the stack.
  B. Disable autonegotiation and replace it with VLACP to identify single fiber fault failure.
  C. Use unique MLT IDs for each stack of edge ERS 5500 switches.
  D. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.
  B. Disable autonegotiation and replace it with VLACP to identify single fiber fault failure.

• Question 44:

  Refer to the exhibit.

  

  Simple Loop Prevention Protocol (SLPP) provides active protection against Layer 2 network loops on a per-VLAN basis. For the SLPP Tx process, the network administrator decides on which VLANs to enable SLPP. The hello packets are

  then replicated out all ports that are members of the SLPP-enabled VLAN.

  Given the following information shown in the exhibit:

  A = InterSwitch Trunk (IST)

  B = Split MultiLink Trunk (SMLT)

  # 1 VSP 9000

  # 2 VSP 9000

  # 3 ERS 4500

  When setting up the SLPP Rx process, which configuration role is setup on VSP #1?

  A. The VSP #1 Rx process is enabled on all SMLT VLANs to monitor for the ERS #3 SLPP packets.
  B. The VSP #1 Rx process is enabled on port 3/1 and the IST ports to monitor for the VSP #2 SLPP packets.
  C. The VSP # 1 Rx process is enabled on all SMLT VLANs to monitor for the VSP # 2 SLPP packets.
  D. The VSP # 1 RX process is enabled on port 3/1 to monitor VSP # 1 and VSP #2 SLPP packets.
  B. The VSP #1 Rx process is enabled on port 3/1 and the IST ports to monitor for the VSP #2 SLPP packets.

• Question 45:

  On an ERS 8000, which command is used to see the state of an installed interface card?

  A. show state
  B. show installed
  C. show slot state all
  D. show slot
  D. show slot

• Question 46:

  When configuring an Ethernet Routing Switch (ERS) 8000 for Split Multi Link Trunking (SMLT), protection against an edge switch in the factory default condition must be taken into consideration. Which parameter will help prevent loops on the SMLT ports?

  A. Enable SLPP.
  B. Discard Looped Frames.
  C. Enable Spanning Tree.
  D. Enable LACP.
  A. Enable SLPP.

• Question 47:

  Given the following syntax:

  config ethernet ip create [mac_offset ]

  Which action is depicted in the command above?

  A. Assign an IP address and a VLAN Id to the module.
  B. Assign the DNS attributes and a server to the switch.
  C. Assign an IP address and a VLAN Id to a port.
  D. Assign the DHCP attributes to a given VLAN.
  C. Assign an IP address and a VLAN Id to a port.

• Question 48:

  Refer to the exhibit.

  

  A technician has just enabled SLPP on both core switches, and is reviewing the network diagram and console output from the core 1 Ethernet Routing Switch (ERS) 8000. Given the output shown in the exhibit, what is the configuration error on the edge switch?

  A. The edge switch spanning-tree has not been configured.
  B. The edge switch access port rate limiting has not been configured.
  C. The edge MLT has not been configured.
  D. The edge VLANs have not been configured.
  C. The edge MLT has not been configured.

• Question 49:

  Refer to the exhibit.

  

  While troubleshooting your VSP 9000 system, you run the command flight-recorder all 1. The associated files ace created. Based on the information in the exhibit, where are the associated files stored?

  A. Internal flash
  B. TFTP Server
  C. External flash
  D. USB Flash device
  A. Internal flash

• Question 50:

  Refer to the exhibit.

  

  The EDM is used to see the configured routes within your system.

  Based on the information in the exhibit, what is the problem with the route to the 10.0.0.0 network?

  A. The route has a metric of 1.
  B. The route is inactive.
  C. The route is not configured.
  D. The route has no next hop.
  B. The route is inactive.