Avaya 6103 Online Practice Questions and Exam Preparation

Avaya 6103 Online Questions & Answers

• Question 21:

  In the current business environment everyone is being asked to do more with fewer physical resources. Using virtualization allows the Virtual Services Platform (VSP) 9000 to increase the services provided. By using VRF-Lite, what does the VSP 9000 eliminate the need for?

  A. SMLT
  B. RSMLT
  C. Non-overlapping addresses
  D. Multiple physical routers
  D. Multiple physical routers

• Question 22:

  A customer has a edge switch connected to a cluster of VSP 9000 switches. The uplinks to the network core are via two Gigabit uplink ports. The uplinks are not aggregated and are running spanning tree protocol.

  The result is that one of the links is always being blocked, and recovery time is unacceptably long when the active uplink fails. They need to have both links active to increase the bandwidth to the core, and at the same time provide better

  redundancy.

  What is the preferred Avaya solution for the customer?

  A. Connect both of the uplinks to one of the VSP 9000 switches and disable spanning tree.
  B. Connect one uplink to each of the VSP 9000 switches to create a triangle and use spanning tree protocol.
  C. Connect one uplink to each of the VSP 9000 switches to create a triangle and configure a SMLT with either MLT or LACP on the access switch. Spanning tree must be disabled.
  D. Connect one uplink to each of the VSP 9000 switches to create a triangle and configure a SMLT with either MLT or LACP on the access switch. Spanning tree must be enabled.
  D. Connect one uplink to each of the VSP 9000 switches to create a triangle and configure a SMLT with either MLT or LACP on the access switch. Spanning tree must be enabled.

• Question 23:

  Both the VSP 9000 and ERS 8000 systems support Custom Auto-Negotiation Advertisements (CANA).

  These advertisement messages are used by both ends of a link.

  What information do these messages determine?

  A. Speed and Duplex
  B. Speed and Link type
  C. Speed and Protocol
  D. Speed and link status
  A. Speed and Duplex

• Question 24:

  Once you have enabled the web server within the system for EDM access, what is the syntax to allow only secure connections?

  A. web-server secure-only
  B. web-server ssh enable
  C. web-server secure enable
  D. web-server ssh session only
  A. web-server secure-only

• Question 25:

  In a VSP 9000 chassis, which command is used to see the information on the installed software?

  A. show software
  B. show sys installed
  C. show sys software
  D. show sys boot
  C. show sys software

• Question 26:

  The VSP9000 uses three distinct traffic management profiles, configured with the boot config flag fabric-profile command. What is the default profile in the VSP9000?

  A. Balanced Profile
  B. Unicast Optimized
  C. Multicast Optimized
  D. None, the profile must be set
  A. Balanced Profile

• Question 27:

  When configuring a new Ethernet Routing Switch (ERS) 8000 using the default interface, the attempt to load an ACLI configuration fails because the default interface is the CLI. How is the ACLI interface obtained?

  A. by changing the interface type in the config.cfg file
  B. by changing the ACLI boot flag and saving the boot configuration file
  C. by exiting the CLI and choosing ACLI at the interface manager prompt
  D. by use the abort command, and entering 'no' at the default interface prompt
  C. by exiting the CLI and choosing ACLI at the interface manager prompt

• Question 28:

  Refer to the exhibit.

  

  After checking the VLAN configuration using the show vlan info basic, and the show vlan info port commands, there are no ACTIVE MEMBER ports for VLAN-50. What is causing this problem?

  A. The ports have not been configured as active for this VLAN.
  B. AppleTalk Protocol VLANs do not have ACTIVE MEMBERS.
  C. The default setting for this type of VLAN is potential.
  D. There are no devices connected to these ports.
  A. The ports have not been configured as active for this VLAN.

• Question 29:

  On the VSP 9000, there are a maximum of 256 VRRP instances per VRF.

  What is the maximum number of instances that are allowed on the system?

  A. 256
  B. 512
  C. 768
  D. 1024
  B. 512

• Question 30:

  A port on the Virtual Services Platform (VSP) 9000 is down because of a link_flap condition as shown in the following output:

  VSP-9012:1#show interfaces gigabitEthernet state 10/8 ================================================================ Port State ================================================================ PORT NUM ADMINSTATUS PORTSTATE REASON DATE -------------------------------------------------------------------------------------------------- 10/8 up down LINK-FLAP 10/28/10 00:22:50

  What is the most likely cause?

  A. The spanning tree protocol has detected a loop and placed the port in a blocked state.
  B. There is a physical problem, such as a cable problem.
  C. One side of the connection is configured for auto-negotiation and the other side is a fixed speed.
  D. The port is receiving a large number of destination unknown broadcast packets.
  D. The port is receiving a large number of destination unknown broadcast packets.