Avaya 6103 Online Practice Questions and Exam Preparation

Avaya 6103 Online Questions & Answers

• Question 11:

  After configuring your VSP 9000 for web access, engineers on the team says that they cannot log into EDM using their credentials. What are the default credentials for EDM?

  A. username: admin password: password
  B. username: rwa password: rwa
  C. username: admin password:
  D. username: avaya password: avaya
  A. username: admin password: password

• Question 12:

  Given the following command:

  VSP-9012:1S show khi performance

  Which Key Health Indicator is only valid for the CP modules?

  A. CPU
  B. buffer-pool
  C. error-count
  D. process
  E. memory
  A. CPU

• Question 13:

  Flight Recorder can be used on the Virtual Services Platform (VSP) 9000 to help Identify problems. When can a Flight Recorder snapshot be taken?

  A. when the VSP has to be booted into the diagnostic mode
  B. only after a warning message is logged
  C. anytime
  D. every hour
  B. only after a warning message is logged

• Question 14:

  On the VSP 9000 and ERS 8000, the Switch Fabric (SF) modules are installed to intelligently switch or route traffic coming into the chassis. What determines the SF module function on the VSP 9000?

  A. campus size
  B. module type
  C. software version
  D. slot location
  D. slot location

• Question 15:

  Which statement describes how to configure Simple Loop Prevention protocol (SLPP) Rx?

  A. SLPP is configured on the edge switch ports that connect to the core switch cluster.
  B. SLPP is configured on the Inter Switch Trunk (IST) ports of the core switch cluster.
  C. SLPP is configured on the core switch cluster ports that connect to the edge switch.
  D. SLPP is configured on the uplink ports of both the core switch cluster and the edge switch.
  B. SLPP is configured on the Inter Switch Trunk (IST) ports of the core switch cluster.

• Question 16:

  Which statement about the local router MAC addresses on RSMLT aggregation switches (cluster) is true?

  A. On a RSMLT aggregation switch pair, local router MAC addresses are exchanged, and only used in case of switch failure.
  B. On a RSMLT aggregation switch pair, local router MAC addresses are exchanged, and always used for data forwarding.
  C. On a RSMLT aggregation switch pair, the virtual MAC address is exchanged, and used for data forwarding.
  D. RSMLT aggregation switches are not exchanging local router MAC addresses, but are using the IP destination address to forward traffic.
  B. On a RSMLT aggregation switch pair, local router MAC addresses are exchanged, and always used for data forwarding.

• Question 17:

  An engineer is configuring the VSP 9000 for EDM management, and cannot connect from the EDM computer to the VSP 9000. Once logged into the ACLI, which show command is used to see the status of the web server?

  A. show vsp edm server
  B. show ip web-server
  C. show sys webserver
  D. show web-server
  D. show web-server

• Question 18:

  While troubleshooting the VSP 9000 system, a technician notices that one port Link/Activity LED is blinking constantly or is nearly solid. This could be an indication of mis-configuration or high traffic volume. Using the CLI, what is the logical first step in troubleshooting this situation?

  A. Verify the port configuration parameters on the VSP 9000 system.
  B. Verify that there is not a broadcast storm by mirroring the traffic on that port.
  C. Verify the port configuration parameters on both ends of the connection.
  D. Verify the cable type and connectors on both ends of the connection.
  C. Verify the port configuration parameters on both ends of the connection.

• Question 19:

  When troubleshooting an issue with an ERS 8000, running version 7.2, a technician notices that the "Online" LED is steady amber for longer than 3 minutes. This is an indication of a software incompatibility. What is the first step in resolving this issue?

  A. Use the show chassis command to look for software versions running on the switch.
  B. Use the show compatibility command to verify that all software running is compatible.
  C. Reboot the switch using the boot flags to force the switch to auto-update the software.
  D. Use the show log command to check the system log for indications of communication problems.
  D. Use the show log command to check the system log for indications of communication problems.

• Question 20:

  During a power-on or cold-start sequence, at which stage can the flags to change the operational environment of the switch be set?

  A. the boot monitor prompt
  B. the image search
  C. the system test
  D. the boot configuration prompt
  A. the boot monitor prompt