Avaya Avaya Certifications 6103 Questions & Answers

• Question 31:

  How do the Switch Fabric (SF) modules provide bandwidth management across the I/O modules?

  A. The bandwidth management is handled by the CP modules.

  B. SF modules in slots SF1 and SF4 provide bandwidth management across the I/O modules.

  C. Bandwidth management is shared across all installed SF modules.

  D. The SF module in slot SF1 provides bandwidth management for the I/O modules in slots 1-5, while the SF module in slot SF4 provides bandwidth management for slots 6-10.

  E. The SF module in slot SF1 provides bandwidth management for even numbered slots (2,4,6,8,10), while the SF module in slot SF4 provides bandwidth management for odd numbered I/O slots (1,3,5,7,9).

  Correct Answer: B

• Question 32:

  Which command mode contains the commands needed to work on software licenses?

  A. User Exec

  B. Global Configuration

  C. Software Configuration

  D. Privileged Exec

  Correct Answer: B

• Question 33:

  A technician has installed the Advanced License. After initial configuration of an ERS 8000 system, the technician must also configure VRF for use on the network.

  Which license enables the use of VRF?

  A. the Advanced license

  B. the Premier license

  C. the Base license

  D. the VRF License

  Correct Answer: B

• Question 34:

  Once created, which ACLI command line syntax is used to see that an instance of VRF is configured correctly?

  A. show ip all vrf

  B. show sys vrf

  C. show vrf ip all

  D. show ip vrf

  Correct Answer: D

• Question 35:

  Given the following error message:

  Power Supply Down(PsID=1,OperStatus=4)

  What does the error message mean regarding the power supply?

  A. It has failed.

  B. It is installed,

  C. It is intermittent.

  D. It is missing.

  Correct Answer: A

• Question 36:

  Which ACLI command is used to display SMLT port configuration?

  A. show port smlt {fastethernet|gigabitethernet|mlt|pos}

  B. show mlt {fastethernet|gigabitethernet|mlt|pos}

  C. show smlt {fastethernet|gigabitethernet|mlt|pos}

  D. show port info mlt {fastethernet|gigabitethernet|mlt|pos}

  Correct Answer: D

• Question 37:

  Refer to the exhibit.

  

  While troubleshooting your VSP 9000 system, you run the command flight-recorder all

  1. The associated files ace created.

  Based on the information in the exhibit, where are the associated files stored?

  A. Internal flash

  B. TFTP Server

  C. External flash

  D. USB Flash device

  Correct Answer: A

• Question 38:

  Which CLI command is used to validate that synchronization for High Availability mode is correct?

  A. show ha-info

  B. show ha-all

  C. show ha-state

  D. show ha-sync

  Correct Answer: A

• Question 39:

  Within an STP enabled ERS 8000 switch, what will the vlan create name type port command create?

  A. a port based VLAN

  B. an ACL for a VLAN

  C. a protocol based VLAN

  D. a named VLAN

  Correct Answer: A

• Question 40:

  Refer to the exhibit.

  

  After checking the VLAN configuration using

  the show vlan info basic, and the show

  vlan info port commands, there are no ACTIVE MEMBER ports for VLAN-50.

  What is causing this problem?

  A. The ports have not been configured as active for this VLAN.

  B. AppleTalk Protocol VLANs do not have ACTIVE MEMBERS.

  C. The default setting for this type of VLAN is potential.

  D. There are no devices connected to these ports.

  Correct Answer: A