Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 591:

  Which language defines the structure or modeling of data for NETCONF and RESTCONF?

  A. YAML
  B. YANG
  C. JSON
  D. XML
  B. YANG

• Question 592:

  A network administrator is configuring a configuration management tool for some network devices that does not support agent.

  Which option will successfully configure management tool for that device?

  A. Agent based Configuration
  B. Agent Less Configuration
  C. Proxy-agent Configuration
  D. None of the above
  B. Agent Less Configuration

• Question 593:

  To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.

  Which EtherChannel mode must be configured on the switch to allow the WLC to connect?

  A. Auto
  B. Active
  C. On
  D. Passive
  C. On

  ---

  Explanation

  Link aggregation (LAG) is a partial implementation of the 802.3ad port aggregation standard. It bundles all of the controller's distribution system ports into a single 802.3ad port channel.

  Restriction for Link aggregation:

  + LAG requires the EtherChannel to be configured for `mode on' on both the controller and the Catalyst switch. ...

  References:

  https://community.cisco.com/t5/wireless-mobility-documents/lag-link-aggregation/ta-p/3128669

• Question 594:

  SIMULATION

  

  

  A. See the solution below in Explanation.
  B. Place Holder
  C. Place Holder
  D. Place Holder
  A. See the solution below in Explanation.

  ---

  Explanation

  R22

  int tun0

  vrf forwarding FINANCE

  ip add 10.10.10.2 255.255.255.0

  tunn source e0/0

  tunnel dest 209.165.200.230

  no shut

  ip route vrf FINANCE 10.10.111.0 255.255.255.0 tunn0 int et0/1

  vrf forwarding FINANCE

  ip address 10.22.22.1 255.255.255.252

  wr Verification:

  

  

  OR

  

  

• Question 595:

  A Cisco administrstor deploys a new wireless network but CAPWAP APs cannot communicate with the wireless controller. IP connectivity in the network functions properly.

  Which action resolves the issue?

  A. Open CAPWAP UDP port 12222 in the network firewall.
  B. Open CAPWAP UDP ports 5246 and 5247 in the network firewall.
  C. Enable the UDP Lite feature on the WLC.
  D. Ensure that the controller is connected to a AAA server.
  B. Open CAPWAP UDP ports 5246 and 5247 in the network firewall.

• Question 596:

  

  Refer to the exhibit.

  Which two commands are required on router R1 to block FTP and allow all other traffic from the Branch 2 network? (Choose two.)

  A. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp-data access-list 101 permit ip any any
  B. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp-data access-list 101 permit ip any any
  C. interface GigabitEthernet0/0 ip address 10.0.0.1 255.255.255.252 ip access-group 101 out
  D. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp access-list 101 permit ip any any
  E. interface GigabitEthernet0/0 ip address 10.0.101.1 255.255.255.252 ip access-group 101 in
  A. access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp access-list 101 deny tcp 10.0.2.0 0.0.0.255 host 10.0.101.3 eq ftp-data access-list 101 permit ip any any
  C. interface GigabitEthernet0/0 ip address 10.0.0.1 255.255.255.252 ip access-group 101 out

• Question 597:

  In a wireless network environment, what is calculated using the numerical values of the transmitter power level, cable loss, and antenna gain?

  A. EIRP
  B. dBi
  C. RSSI
  D. SNR
  A. EIRP

  ---

  Explanation

  Once you know the complete combination of transmitter power level, the length of cable, and the antenna gain, you can figure out the actual power level that will be radiated from the antenna. This is known as the effective isotropic radiated power (EIRP), measured in dBm. EIRP is a very important parameter because it is regulated by governmental agencies in most countries. In those cases, a system cannot radiate signals higher than a maximum allowable EIRP. To find the EIRP of a system, simply add the transmitter power level to the antenna gain and subtract the cable loss.

• Question 598:

  Refer to the exhibit.

  

  What is output by this code?

  A. 0 5
  B. 0 1 2 3 4 5
  C. 0 1 2 3 4
  D. (0,5)
  B. 0 1 2 3 4 5

• Question 599:

  Refer to the exhibit.

  

  Traffic is not passing between SW1 and SW2.

  Which action fixes the issue?

  A. Configure LACP mode on S1 to passive.
  B. Configure switch port mode to ISL on S2.
  C. Configure PAgP mode on S1 to desirable.
  D. Configure LACP mode on S1 to active.
  C. Configure PAgP mode on S1 to desirable.

• Question 600:

  

  Refer to the exhibit.

  Why was the response code generated?

  A. The resource was unreachable.
  B. Access was denied based on the user permissions.
  C. Access was denied based on the credentials.
  D. The resource is no longer available on the server.
  B. Access was denied based on the user permissions.

  ---

  Explanation

  401 = Unauthorized (Bad credentials) 403 = Forbidden (Service refused, for insufficient permissions)