Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 261:

  What is a characteristic of Cisco StackWise technology?

  A. It uses proprietary cabling
  B. It supports devices that are geographically separated
  C. lt combines exactly two devices
  D. It is supported on the Cisco 4500 series.
  A. It uses proprietary cabling

  ---

  Explanation

  References:

  https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-9200-series-switches/nb-06-stackwise-architecture-cte-en.html

• Question 262:

  Refer to the exhibit.

  

  An engineer must ensure that all traffic leaving AS 200 will choose Link 2 as the exit point.

  Assuming that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers, which configuration accomplishes this task?

  A. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 200 200 200 R3(config)#router bgp 200 R3#(config-router)#neighbor 10.1.1.1 route-map PREPEND out
  B. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 100 100 100 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND in
  C. R4(config)#route-map PREPEND permit 10 R4(config-route-map)#set as-path prepend 200 200 200 R4(config)#router bgp 200 R4(config-router)#neighbor 10.2.2.2 route-map PREPEND out
  D. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 100 100 100 R3(config)#router bgp 200 R3(config-router)#neighbor 10.1.1.1 route-map PREPEND in
  A. R3(config)#route-map PREPEND permit 10 R3(config-route-map)#set as-path prepend 200 200 200 R3(config)#router bgp 200 R3#(config-router)#neighbor 10.1.1.1 route-map PREPEND out

  ---

  Explanation

  R3 advertises BGP updates to R1 with multiple AS 100 so R3 believes the path to reach AS 200 via R3 is farther than R2 so R3 will choose R2 to forward traffic to AS 200.

• Question 263:

  Refer to the exhibit.

  

  Which level message does the WLC send to the syslog server?

  A. syslog level errors and less severity messages
  B. syslog level errors messages
  C. all syslog levels messages
  D. syslog level errors and greater severity messages
  A. syslog level errors and less severity messages

  ---

  Explanation

  If you set a syslog level, only those messages whose severity is equal to or less than that level are sent to the syslog servers. For example, if you set the syslog level to Notifications (severity level 5), only those messages whose severity is betwen 0 and 5 are sent to the syslog servers.

  https://www.cisco.com/c/en/us/support/docs/wireless/4100-series-wireless-lan-controllers/107252-WLC-Syslog-Server.html

• Question 264:

  SIMULATION

  Guidelines

  This is a lab item in which tasks will be performed on virtual devices.

  1. Refer to the Tasks tab to view the tasks for this lab item.

  2. Refer to the Topology tab to access the device console(s) and perform the tasks.

  3. Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

  4. All necessary preconfigurations have been applied.

  5. Do not change the enable password or hostname for any device.

  6. Save your configurations to NVRAM before moving to the next item.

  7. Click Next at the bottom of the screen to submit this lab and move to the next question.

  8. When Next is clicked, the lab closes and cannot be reopened.

  Topology

  

  Tasks

  Configure OSPF on both routers according to the topology to achieve these goals:

  1. Ensure that all networks are advertised between the routers without using the "network" statement under the "router ospf" configuration section.

  2. Configure a single command on both routers to ensure:

  The DR/BDR election does not occur on the link between the OSPF neighbors.

  No extra OSPF host routes are generated.

  A. See the solution below in Explanation.
  B. Place Holder
  C. Place Holder
  D. Place Holder
  A. See the solution below in Explanation.

  ---

  Explanation

  Solution:

  R1

  Router ospf 1

  Int loop0

  Ip ospf 1 area 0

  Int et0/0

  Ip ospf 1 area 0

  Ip ospf network point-to-point

  Copy run start

  R2

  Router ospf 1

  Int loop0

  Ip ospf 1 area 0

  Int et0/0

  Ip ospf 1 area 0

  Ip ospf network point-to-point

  Copy run start

  Verification:-

  

  

• Question 265:

  What does the statement print(format(0.8, '.

  0%')) display?

  A. 80%
  B. 8%
  C. 0.8%
  D. 8.8%
  A. 80%

• Question 266:

  Refer to the exhibit.

  

  R1 and R2 are on the same VLAN. VRRP is configured between the two routers.

  What is the cause of the VRRP error?

  A. R1 is configured with VIP 10.18.0.2 on VRRP group 1 and R2 is configured with VIP 10.18.0.1 on VRRP group 1.
  B. R1 is configured with VIP 10.18.0.2 on VRRP group 1 and R2 is configured with VIP 10.18.0.2 on VRRP group 1.
  C. R1 is configured with VIP 10.18.0.1 on VRRP group 1 and R2 is configured with VIP 10.18.0.2 on VRRP group 0.
  D. R1 is configured with VIP 10.18.0.1 on VRRP group 1 and R2 is configured with VIP 10.18.0.2 on VRRP group 1.
  D. R1 is configured with VIP 10.18.0.1 on VRRP group 1 and R2 is configured with VIP 10.18.0.2 on VRRP group 1.

• Question 267:

  What is a characteristics of traffic policing?

  A. lacks support for marking or remarking
  B. must be applied only to outgoing traffic
  C. can be applied in both traffic directions
  D. queues out-of-profile packets until the buffer is full
  D. queues out-of-profile packets until the buffer is full

• Question 268:

  What is a characteristic of traffic shaping?

  A. drops out-of-profile packets
  B. causes TCP retransmits when packets are dropped
  C. can be applied in both traffic directions
  D. queues out-of-profile packets until the buffer is full
  D. queues out-of-profile packets until the buffer is full

• Question 269:

  Refer to the exhibit.

  

  The WLC administrator sees that the controller to which a roaming client associates has Mobility Role Anchor configured under Clients > Detail.

  Which type of roaming is supported?

  A. Indirect
  B. Layer 3 intercontroller
  C. Layer 2 intercontroller
  D. Intercontroller
  B. Layer 3 intercontroller

  ---

  Explanation

  What is a Mobility Anchor?

  Mobility Anchor, also referred to as Guest tunneling or Auto Anchor Mobility, is a feature where all the client traffic that belongs to a WLAN (Specially Guest WLAN) is tunneled to a predefined WLC or set of controllers that are configured as Anchor for that specific WLAN. This feature helps to restrict clients to a specific subnet and have more control over the user traffic. Refer to theConfiguring Auto-Anchor Mobilitysection of Cisco Wireless LAN Controller Configuration Guide, Release 8.8for more information on this feature.

  This would be a L3 Roam as the client is Anchored to the AP with a CAPWAP tunnel formed between the Anchor WLC and the associated WLC

  https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/107188-mobility-groups-faq.html#anc15

• Question 270:

  "HTTP/1.1 204 No Content" is returned when the curl -i -X DELETE command is issued.

  Which situation has occurred?

  A. The object could not be located at the URI path.
  B. The command succeeded in deleting the object.
  C. The object was located at the URI, but it could not be deleted.
  D. The URI was invalid.
  B. The command succeeded in deleting the object.

  ---

  Explanation

  The HTTP 204 No Content success status response code indicates that a request has succeeded, but that the client doesn't need to navigate away from its current page.