Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 231:

  Which capability does a distributed virtual switch have?

  A. use floating static routes
  B. provide configuration consistency across the hosts
  C. run dynamic routing protocols
  D. use advanced IPsec encryption algorithms
  B. provide configuration consistency across the hosts

• Question 232:

  DRAG DROP

  Drag and drop the characteristics from the left onto the technology types on the right.

  Select and Place:

  

  

• Question 233:

  DRAG DROP

  Drag and drop the automation characteristics from the left onto the appropriate tools on the right. Not all options are used.

  Select and Place:

  

  

• Question 234:

  SIMULATION

  Guidelines

  This is a lab item in which tasks will be performed on virtual devices.

  1. Refer to the Tasks tab to view the tasks for this lab item.

  2. Refer to the Topology tab to access the device console(s) and perform the tasks.

  3. Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

  4. All necessary preconfigurations have been applied.

  5. Do no remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.

  6. Do not change the enable password or hostname for any device.

  7. Save your configurations to NVRAM before moving to the next item.

  8. Click Next at the bottom of the screen to submit this lab and move to the next question 9. When Next is clicked, the lab closes and cannot be reopened.

  Topology

  

  Tasks

  OSPF is partially configured. Complete the OSPF configurations to achieve these goals:

  1. Configure OSPF on router R1 according to the topology so that all networks are advertised. Do not use the network statement under the “router ospf” configuration section to accomplish this task.

  2. Configure a single command on the ABR routers to ensure only one summary route is advertised to area 0.

  R1

  

  

  

  

  

  

  

  

  

  

  

  A. See the solution below in Explanation.
  B. Place Holder
  C. Place Holder
  D. Place Holder
  A. See the solution below in Explanation.

  ---

  Explanation

  R1:

  To advertise all connected networks without using the network statement, we will configure OSPF on each

  interface:

  Router#configure terminal

  Enter configuration commands, one per line. End with END or Ctrl-Z.

  R1(config)#interface Ethernet0/0

  R1(config-if)#ip ospf 1 area 0

  R1(config-if)#end

  R1(config)#interface Ethernet0/1

  R1(config-if)#ip ospf 1 area 0

  R1(config-if)#end

  R1(config)#interface Ethernet0/2

  R1(config-if)#ip ospf 1 area 10

  R1(config-if)#end

  R1(config)#end

  To ensure only one summary route is advertised to Area 0, we can use the summary-address command

  on the ABRs. In this case, we'll summarize the entire Area 10:

  R2:

  R2#configure terminal

  Enter configuration commands, one per line. End with END or Ctrl-Z.

  R2(config)#router ospf 1

  R2(config-router)#summary-address 10.1.0.0 255.255.0.0

  R2(config-router)#exit

  R2(config)#end

  R3:

  R3#configure terminal

  Enter configuration commands, one per line. End with END or Ctrl-Z.

  R3(config)#router ospf 1

  R3(config-router)#summary-address 10.2.0.0 255.255.0.0

  R3(config-router)#exit

  R3(config)#end

• Question 235:

  A network is being migrated from IPV4 to IPV6 using a dual-stack approach. Network management is already 100% IPV6 enabled.

  In a dual-stack network with two dual-stack NetFlow collections, how many flow exporters are needed per network device in the flexible NetFlow configuration?

  A. 1
  B. 2
  C. 4
  D. 8
  B. 2

  ---

  Explanation

  A dual-stack device is a device with network interfaces that can originate and understand both IPv4 and IPv6 packets.

  It is because each flow collector can only send to a single destination. In this question there are two NetFlow collectors... thus two destination. Thus the need for 2 flow exporters. Each flow exporter supports only one destination. If you want to export the data to multiple destinations, you must configure multiple flow exporters and assign them to the flow monitor.

  You can export to a destination using either an IPv4 or IPv6 address.

  https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/fnetflow/configuration/15-mt/fnf-15-mt-book/cfg-de-fnflow-exprts.html

  Look under the section "Configuring the Flow Exporter"

• Question 236:

  A wireless administrator must create a new web authentication corporate SSID that will be using ISE as the external RADIUS server. The guest VLAN must be specified after the authentication completes. Which action must be performed to allow the ISE server to specify the guest VLAN?

  A. Enable AAA Override.
  B. Enable Network Access Control State.
  C. Set AAA Policy name.
  D. Set RADIUS Profiling.
  A. Enable AAA Override.

• Question 237:

  What is YANG used for?

  A. scraping data via CLI
  B. processing SNMP read-only polls
  C. describing data models
  D. providing a transport for network configuration data between client and server
  C. describing data models

  ---

  Explanation

  YANG is used to model each protocol based on RFC 6020.

  https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/datamodels/configuration/xe-16/data-models-xe-16-book/yang-netconf.html

• Question 238:

  Which DNS record type is needed to allow a Cisco AP to discover a WLC when using IPv4?

  A. CNAME record
  B. A record
  C. NS record
  D. SOA record
  A. CNAME record

• Question 239:

  DRAG DROP

  Drag and drop the characteristics from the left onto the routing protocols they describe on the right.

  Select and Place:

  

  

• Question 240:

  Refer to the exhibit.

  

  After implementing the configuration 172.20.20.2 stops replaying to ICMP echoes, but the default route fails to be removed. What is the reason for this behavior?

  A. The source-interface is configured incorrectly.
  B. The destination must be 172.30.30.2 for icmp-echo
  C. The default route is missing the track feature
  D. The threshold value is wrong.
  C. The default route is missing the track feature

  ---

  Explanation

  The last command should be "R1(config)#ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10".