1. Home
  2. Cisco
  3. 350-401

Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)

Exam Details

  • Exam Code
    :350-401
  • Exam Name
    :Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR)
  • Certification
    :CCNP Enterprise
  • Vendor
    :Cisco
  • Total Questions
    :1457 Q&As
  • Last Updated
    :May 07, 2025

Cisco CCNP Enterprise 350-401 Questions & Answers

  • Question 1111:

    Which devices does Cisco DNA Center configure when deploying an IP-based access control policy?

    A. All devices integrating with ISE

    B. selected individual devices

    C. all devices in selected sites

    D. all wired devices

  • Question 1112:

    Refer to the exhibit.

    Which set of commands on router r R1 Allow deterministic translation of private hosts PC1, PC2, and PC3 to addresses in the public space?

    A. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#access-list 1 10.10.10.0 0.0.0.255 RouterR1(config)#ip nat inside source list 1 interface f0/1 overload

    B. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#access-list 1 10.10.10.0 0.0.0.255 RouterR1(config)#ip nat pool POOL 155.1.1.101 155.1.1.103 netmask 255.255.255.0 RouterR1(config)#ip nat inside source list 1 pool POOL

    C. RouterR1(config)#int f0/0 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#ip nat inside source static 10.10.10.101 155.1.1.101 RouterR1(config)#ip nat inside source static 10.10.10.102 155.1.1.102 RouterR1(config)#ip nat inside source static 10.10.10.103 155.1.1.103

    D. RouterR1(config)#int f0/0 RouterR1(config)#ip nat outside RouterR1(config)#exit RouterR1(config)#int f0/1 RouterR1(config)#ip nat inside RouterR1(config)#exit RouterR1(config)#ip nat inside source static 10.10.10.101 155.1.1.101 RouterR1(config)#ip nat inside source static 10.10.10.102 155.1.1.102 RouterR1(config)#ip nat inside source static 10.10.10.103 155.1.1.103

  • Question 1113:

    Which device makes the decision for a wireless client to roam?

    A. wireless client

    B. wireless LAN controller

    C. access point

    D. WCS location server

  • Question 1114:

    An engineer must provide wireless converge in a square office. The engineer has only one AP and believes that it should be placed it in the middle of the room. Which antenna type should the engineer use?

    A. directional

    B. polarized

    C. Yagi

    D. omnidirectional

  • Question 1115:

    Refer to the exhibit. Which action resolves the EtherChannel issue between SW2 and SW3?

    A. Configure switchport mode trunk on SW2.

    B. Configure switchport nonegotiate on SW3

    C. Configure channel-group 1 mode desirable on both interfaces.

    D. Configure channel-group 1 mode active on both interfaces.

  • Question 1116:

    Refer to the exhibit.

    An engineer attempts to configure a trunk between switch SW1 and switch SW2 using DTP, but the trunk does not form. Which command should the engineer apply to switch SW2 to resolve this issue?

    A. switchport mode dynamic desirable

    B. switchport mode access

    C. no switchport

    D. switchport nonegotiate

  • Question 1117:

    What is the purpose of the LISP routing and addressing architecture?

    A. It creates two entries for each network node, one for Its identity and another for its location on the network.

    B. It allows LISP to be applied as a network visualization overlay though encapsulation.

    C. It allows multiple Instances of a routing table to co-exist within the same router.

    D. It creates head-end replication used to deliver broadcast and multicast frames to the entire network.

  • Question 1118:

    Refer to the exhibit.

    Based on the configuration in this WLAN security setting, which method can a client use to authenticate to the network?

    A. text string

    B. username and password

    C. certificate

    D. RADIUS token

  • Question 1119:

    What is a fact about Cisco EAP-FAST?

    A. It does not require a RADIUS server certificate.

    B. It requires a client certificate.

    C. It is an IETF standard.

    D. It operates in transparent mode.

  • Question 1120:

    In a Cisco SD-Access solution, what is the role of the Identity Services Engine?

    A. It is leveraged for dynamic endpoint to group mapping and policy definition.

    B. It provides GUI management and abstraction via apps that share context.

    C. it is used to analyze endpoint to app flows and monitor fabric status.

    D. It manages the LISP EID database.

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 350-401 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.