Cisco 350-029 Online Practice Questions and Exam Preparation

Cisco 350-029 Online Questions & Answers

• Question 81:

  Using more than one label on a single packet is required in what context?

  A. MPLS TE
  B. When CEF switching and Label switching is done
  C. In all the above circumstances.
  D. MPLS VPN
  D. MPLS VPN

• Question 82:

  Which statement about VPNv6 addresses is true?

  A. The VPNv6 address is a 96-bit route distinguisher and a 128-bit IPv6 address
  B. The VPNv6 address is a 64-bit route distinguisher and a 128-bit IPv6 address
  C. The VPNv6 address is a 64-bit route distinguisher and a 96-bit IPv6 address
  D. The VPMv6 address is a 96-bit route distinguisher and a 96-bit IPv6 address
  E. The VPNv6 address is a 128-bit route distinguisher and a 128-bit IPv6 address
  B. The VPNv6 address is a 64-bit route distinguisher and a 128-bit IPv6 address

• Question 83:

  What is the payload capacity of an SDH/STM1 circuit?

  A. 155.52 Mbps
  B. 150.336 Mbps
  C. 153.472 Mbps
  D. 151.424 Mbps
  B. 150.336 Mbps

• Question 84:

  Which Inter-AS option allows a service provider to provision AToM along with L3VPN provisioning?

  A. MPLS VPN Inter-AS with ASBRs exchanging VPN-IPv4 addresses
  B. MPLS VPN Inter-AS with ASBRs exchanging IPv4 routes and MPLS labels
  C. MPLS VPN Inter-AS Option AB
  D. back-to-back VRFs
  B. MPLS VPN Inter-AS with ASBRs exchanging IPv4 routes and MPLS labels

• Question 85:

  SONET's three layers arE. (Choose three.)

  A. DS1
  B. Frame
  C. Path
  D. Line
  E. Section
  C. Path
  D. Line
  E. Section

  ---

  SONET Layers SONET divides the overhead and transport functions into three layers: Section Line

  Path

  These three layers are associated with both the physical equipment that segments the network and the bytes of information that flows through the network elements.

• Question 86:

  A network engineer is redistributing BGP prefixes into RIP. These prefixes are unreachable in the RIP network. Which the two actions could resolve the issue based on this scenario? (Choose two.)

  A. Enable BGP synchronization.
  B. Enable BGP AS-override.
  C. Rewrite RIP hop count for the redistributed prefixes.
  D. Enable internal BGP redistribution.
  E. Rewrite BGP next hop.
  F. Apply BGP next-hop-self.
  C. Rewrite RIP hop count for the redistributed prefixes.
  D. Enable internal BGP redistribution.

• Question 87:

  Which three statements about L2TPv3 are true? (Choose three)

  A. L2TPv3 Frame Relay support includes only 32-bit DLCI addressing.
  B. L2TPv3 sessions do not support Frame Relay LMI interworking.
  C. Multipoint DLCI is not supported.
  D. To use DCE or a Network-to-Network Interface on a Frame Relay port, you must configure the frame-relayswitching command.
  E. L2TPv3 feature does not support Frame Relay extended addressing.
  C. Multipoint DLCI is not supported.
  D. To use DCE or a Network-to-Network Interface on a Frame Relay port, you must configure the frame-relayswitching command.
  E. L2TPv3 feature does not support Frame Relay extended addressing.

  ---

  Frame Relay-Specific Restrictions

  Frame Relay per-DLCI forwarding and port-to-port trunking are mutually exclusive. L2TPv3 does not support the use of both on the same interface at the same

  time.

  The xconnect command is not supported on Frame Relay interfaces directly. For Frame Relay, the Xconnect is applied under the connect command specifying

  the DLCI to be used. Changing the encapsulation type on any interface removes any existing xconnect command applied to that interface.

  To use DCE or a Network-to-Network Interface (NNI) on a Frame Relay port, you must configure the framerelay switching command.

  The configuration of an L2TPv3 session on a Multilink Frame Relay (MLFR) bundle interface is supported only on Cisco 12000 series Two-Port Channelized

  OC-3/STM-1 (DS1/E1) and Six- Port Channelized T3 (T1) line cards. (For more information, see Binding L2TPv3 Sessions to Multilink Frame Relay Interfaces.)

  Frame Relay policing is nondistributed on the Cisco 7500 series. By configuring Frame Relay policing, you cause traffic on the affected PVCs to be sent to the RSP for processing.

  Frame Relay support is for 10-bit DLCI addresses. Frame Relay Extended Addressing is not supported.

  Multipoint DLCI is not supported.

  The keepalive will automatically be disabled on interfaces that have an Xconnect applied to them, except for Frame Relay encapsulation, which is a requirement for LMI. ꞏStatic L2TPv3 sessions will not support Frame Relay LMI interworking.

• Question 88:

  How many bits are expressed by "::" in the address 2001:DB8::9C0:876A:0:130B?

  A. 32 bits
  B. 28 bits
  C. 44 bits
  D. 64 bits
  E. 0 bits
  A. 32 bits

• Question 89:

  Which of these is not a component of MPLS traffic engineering?

  A. trunk admission control
  B. forwarding traffic to tunnel
  C. information distribution
  D. path selection, calculation, and setup
  E. traffic patterns prediction
  E. traffic patterns prediction

• Question 90:

  Which three options are EIGRP route types? (Choose three.)

  A. internal routE. routes that originate within the AS
  B. summary routE. routes that are summarized in the router
  C. external routE. routes that are redistributed to EIGRP
  D. partial routE. partial routes that are summarized in the router
  E. stub routE. default route that originates in the area
  A. internal routE. routes that originate within the AS
  B. summary routE. routes that are summarized in the router
  C. external routE. routes that are redistributed to EIGRP