Cisco 350-029 Online Practice Questions and Exam Preparation

Cisco 350-029 Online Questions & Answers

• Question 411:

  Which of the following IOS commands cause syslog messages to be stamped with time and dates?

  A. logging datetime on
  B. service timestamps log datetime
  C. service logging datetime
  D. logging timestamps on
  E. logging trap datetime
  B. service timestamps log datetime

  ---

  Service timestamps

  To configure the system to apply a time stamp to debugging messages or system logging messages, use the service timestamps command in global configuration mode. To disable this service, use the no form of this command.

  Service timestamps [debug | log] [uptime | datetime [msec]] [localtime] [show-timezone] [year] no service timestamps [debug | log]

• Question 412:

  In the IS-IS Designated Intermediate System (DIS) election process, which criteria is used for DIS selection?

  A. highest router ID first, then highest priority
  B. highest MAC address first, then highest priority
  C. highest router ID first, then highest MAC address
  D. highest priority first, then highest router ID
  E. highest priority first, then highest MAC address
  E. highest priority first, then highest MAC address

• Question 413:

  What best describes the usage of Route-Target rewrite?

  A. Route-Target Rewrite is mainly used in Inter-AS MPLS-VPN deployments and is configured at the Route-Reflector in originating AS ASBR to avoid misconfiguration in Route-Target assignment for VPN configurations.
  B. Route-Target Rewrite is mainly used in Inter-AS MPLS-VPN deployments and is configured at the ASBR to avoid misconfiguration in Route-Target assignment for VPN configurations.
  C. Route-Target Rewrite is mainly used in Inter-AS MPLS-VPN deployments and is configured at the PE router in originating AS ASBR to avoid misconfiguration in Route-Target assignment for VPN configurations.
  D. None of the above.
  B. Route-Target Rewrite is mainly used in Inter-AS MPLS-VPN deployments and is configured at the ASBR to avoid misconfiguration in Route-Target assignment for VPN configurations.

• Question 414:

  What does the protocol field inside the PPP frame indicate?

  A. the protocol used to determine the authentication method
  B. the protocol used to identify the data in the Information field
  C. the protocol used to carry the PPP frame
  D. the protocol used to decode the FCS field
  E. the protocol used to detect the number of padding bytes
  B. the protocol used to identify the data in the Information field

  ---

  The Protocol field indicates the type of payload packet (e.g. LCP, NCP, IP, IPX, AppleTalk, etc.). The Information field contains the PPP payload; it has a variable length with a negotiated maximum called the Maximum Transmission Unit. By default, the maximum is 1500 octets. It might be padded on transmission; if the information for a particular protocol can be padded, that protocol must allow information to be distinguished from padding.

• Question 415:

  The IPv6 address FE80::656:78FF:FE9A:BCDE is what type of address?

  A. Site-local
  B. Link-local
  C. Multicast
  D. None of the above
  B. Link-local

  ---

  A link-local address is an IPv6 unicast address that can be automatically configured on any interface using the link-local prefix FE80::/10 (1111 1110 10) and the interface identifier in the modified EUI-64 format. Link-local addresses are not necessarily bound to the MAC address (configured in a EUI-64 format). Link-local addresses can also be manually configured in the FE80::/10 format using the ipv6 address link-local command.

• Question 416:

  Drag the T1 parameters on the left to the corresponding category on the right. Not all options are used.

  Select and Place:

  

  

• Question 417:

  Which methods would enable traffic to be forwarded along an MPLS TE tunnel (Choose 4.)

  A. MP-BGP routing
  B. Static routing
  C. Policy routing
  D. Autoroute
  E. Forwarding adjacency
  B. Static routing
  C. Policy routing
  D. Autoroute
  E. Forwarding adjacency

• Question 418:

  In which three scenarios does multihoming in IS-IS work? (Choose three.)

  A. merging Level 1 areas
  B. splitting the Level 1 area
  C. renumbering NSAP addresses
  D. modifying the system ID
  E. merging Level 2 areas
  F. splitting the Level 2 area
  G. creating an alternative path to the exit point
  A. merging Level 1 areas
  B. splitting the Level 1 area
  C. renumbering NSAP addresses

• Question 419:

  If the OSPF protocol is used to connect customer edge (CE) routers to service provider edge (PE) routers in the VPN backbone, which two options best describe the use of SHAM links?

  A. A sham-link is created between any two VPN sites that belong to the same OSPF area and share an OSPF backdoor link
  B. A sham-link is seen as an intra-area link between PE routers, an OSPF adjacency is created and database is exchanged
  C. A sham-link is created between two directly connected PE routers so that it is preferred over the low speed backdoor door
  D. A sham-link is part of OSPF network of MPLS-VPN provider.
  A. A sham-link is created between any two VPN sites that belong to the same OSPF area and share an OSPF backdoor link
  B. A sham-link is seen as an intra-area link between PE routers, an OSPF adjacency is created and database is exchanged

• Question 420:

  Which two VPN Inter-AS options require the no bgp default route-target filter command? (Choose two.)

  A. MPLS VPN Inter-AS with ASBRs exchanging VPN-IPv4 addresses
  B. MPLS VPN Inter-AS with ASBRs exchanging IPv4 routes and MPLS labels
  C. MPLS VPN Inter-AS Option AB
  D. MPLS VPN Carrier Supporting Carrier using LDP and IGP
  E. MPLS VPN Carrier Supporting Carrier with BGP
  F. MPLS VPN eBGP multipath support for CSC
  A. MPLS VPN Inter-AS with ASBRs exchanging VPN-IPv4 addresses
  C. MPLS VPN Inter-AS Option AB