Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 141:

  Refer to the exhibit.

  

  The network administrator must use a scheduler to perform configuration backups every night. After completing the configuration, the administrator discovers that configuration backups occur at 05:15 in the morning instead of at 02:00. Which action resolves the issue?

  A. Activate the scheduler manually at 02:00 local time.
  B. Create a periodic scheduler that runs every 24 hours.
  C. Implement the switch clock to match the local time.
  D. Configure the scheduler within the CONFIG_BACKUP job.
  C. Implement the switch clock to match the local time.

  ---

• Question 142:

  Refer to the exhibit.

  

  A remote device connected to fc 1/2 fails to come online. Which do you configure to resolve the issue?

  A. remote and local ports to be in the correct VSAN
  B. local switch for NPV
  C. remote device for NPIV
  D. port on remote device as an f-port-channel
  A. remote and local ports to be in the correct VSAN

  ---

• Question 143:

  

  Refer to the exhibit. Server 1 and Server 2 are bare-metal Windows-based servers and can exchange ICMP PING messages. However, both servers fail to ping their default gateway. Which action resolves the problem?

  A. Change the MTU value of the server.
  B. Disable Fabric Failover.
  C. Set the native VLAN ID to 10.
  D. Assign the NIC to the pin group.
  C. Set the native VLAN ID to 10.

  ---

• Question 144:

  Refer to the exhibit.

  

  The EEM script overrides all events in the system policy. What should be added to the script to resolve the issue?

  A. event statement
  B. environment variable
  C. event-default action statement
  D. configure terminal action
  A. event statement

  ---

• Question 145:

  

  Refer to the exhibit. A network engineer failed to upgrade the Cisco Nexus switch. Which action must be taken before the upgrade to resolve the issue?

  A. Upgrade to the intermediate software image
  B. Activate the supervisor module using the TFTP protocol
  C. Delete the current NX-OS kickstart software
  D. Copy the EPLD file onto the standby SUP bootflash
  A. Upgrade to the intermediate software image

  ---

• Question 146:

  Refer to the exhibit.

  

  An engineer fails to implement OSPF routing on a Cisco Nexus 9000 Series Switch. Which action resolves the issue?

  A. Enable the OSPF feature.
  B. Remove invalid characters from the command.
  C. Populate the OSPF database.
  D. Wait for the OSPF adjacency to be established.
  A. Enable the OSPF feature.

  ---

• Question 147:

  An engineer configures role-based access control for the Cisco UCS Manager. UserA must be allowed read-only access to the system. These events occur after the system is implemented:

  1.

  UserA attempts to log in but receives an "Authentication Failed" message.

  2.

  UserB successfully logs in by using an administrator role.

  3.

  Both users use valid LDAP passwords.

  Which action resolves the issue?

  A. Enable primary group rules for LDAP providers
  B. Assign a default role policy for remote users
  C. Add locales to the LDAP group map of UserB
  D. Set the default authentication realm to LDAP
  D. Set the default authentication realm to LDAP

  ---

• Question 148:

  Refer to the exhibit.

  

  A network engineer configures OSPF protocol between two Cisco Nexus 7000 Series Switches. The OSPF neighbors fail to synchronize OSPF databases. Which action resolves the issue?

  A. Match the OSPF area between the two devices.
  B. Configure the IP addresses of the interface in the same subnet.
  C. Change the OSPF area type to 2 on n7k-1.
  D. Set the same MTU values on both sides of the link.
  D. Set the same MTU values on both sides of the link.

  ---

• Question 149:

  A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

  A. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels 2) Verify that at least two physical cables between the IOM and fabric interconnect function properly. 3) Check for runtime link down status 4) Reseat the affected IOM.
  B. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level. 2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly. 3) Check for runtime link down status 4) Reseat the affected IOM.
  C. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level. 2) Verify that at least two physical cables between the IOM and fabric interconnect function properly. 3) Check for runtime link down status. 4) Reseat the affected IOM.
  D. 1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels. 2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly. 3) Check for runtime link down status. 4) Reseat the affected IOM.
  B. 1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level. 2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly. 3) Check for runtime link down status 4) Reseat the affected IOM.

  ---

  https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooting_chapter_01001.html

• Question 150:

  Refer to the exhibits.

  

  The server traffic fails to reach the storage array. Which action resolves the issue?

  A. Change the VLAN ID and VSAN ID at both ends.
  B. Change port speed to auto mode.
  C. Remove and add new SFP on both ends.
  D. Reboot and configure the M5K switches.
  C. Remove and add new SFP on both ends.

  ---