Cisco 300-370 Online Practice Questions and Exam Preparation

Cisco 300-370 Online Questions & Answers

• Question 121:

  In your wireless network, a few legacy 802.11b desktops with old Aironet WLAN adapters, like PC4800, fail to associate to the APs. Which probable cause of this issue is true?

  A. AP radios are configured for long preambles, but these clients require short preambles.
  B. All 802.11g rates are set to Enable.
  C. AP radios are configured for short preambles, but these clients require long preambles.
  D. All 802.11g rates are set to Disable.
  A. AP radios are configured for long preambles, but these clients require short preambles.

• Question 122:

  An engineer is troubleshooting why a MAC address was not listed in the MAC table and discovers that the VLAN was enabled only on the interface that data is coming in on. Which change fixes this problem?

  A. Enable outgoing interfaces.
  B. Disable sticky MAC on the access switch.
  C. Remove loop detection on interfaces.
  D. Flush the MAC address table.
  A. Enable outgoing interfaces.

• Question 123:

  Which two EAP types are tunneled? (Choose two.)

  A. EAP-MD5
  B. EAP-MSCHAPv2
  C. PAP
  D. EAP-FAST
  E. EAP-MD6
  B. EAP-MSCHAPv2
  D. EAP-FAST

• Question 124:

  An engineer has discovered that a number of new access points are failing to join the wireless controller module that has been recently enabled on a switch stack of three Cisco Catalyst 3850 switches running 3.02.03 SE version of Cisco IOS-XE. All cables have been verified and all access point switch port configurations are identical.

  Which options is the likely root cause of the issue?

  A. Stacked Cisco Catalyst 3850 switches only support 100 CAPWAP termination licences.
  B. Cisco IOS-XE version 3.02.03 SE supports only access points on the master switch.
  C. The EULA has not been accepted on the switch wireless controller module.
  D. When stacked, the Cisco Catalyst 3850 cannot use the wireless controller module.
  D. When stacked, the Cisco Catalyst 3850 cannot use the wireless controller module.

• Question 125:

  You are designing a wireless network where the majority of clients are 5 GHz iOS devices, with a few 2.4 GHz-only legacy clients. Which way to approach this design is the best?

  A. Design for 2.4 GHz only and ignore legacy clients.
  B. Add a separate SSID to allow the 2.4 GHz devices to connect to the network.
  C. Design for 5 GHz only and ignore legacy clients.
  D. Allow all clients to access the network through the same SSID and prioritize 5 GHz clients.
  D. Allow all clients to access the network through the same SSID and prioritize 5 GHz clients.

• Question 126:

  While you investigate wireless connectivity issues, a user reports that only certain devices are affected. You use a wireless protocol analyzer to capture 802.11 frames. The capture reveals several issues, so you perform an RF survey.

  Which troubleshooting approach are you using?

  A. bottom-up
  B. divide and conquer
  C. top-down
  D. shoot from the hip
  A. bottom-up

• Question 127:

  When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?

  A. through the primary interface of the group
  B. through round robin between interfaces
  C. through interface group definition
  D. through the interface receiving the first response
  B. through round robin between interfaces

• Question 128:

  A client is failing EAP authentication and a debug shows that the server is sending an Access-Reject message. Which action must you take to resolve authentication?

  A. Verify that the Validate server certificate on the client is disabled.
  B. Verify that the client certificates are from the proper CA and server certificate.
  C. Verify that the client server certificate has the proper Windows OIDs.
  D. Verify that the user account is the same in the client certificate.
  E. Verify that the user is using the same password that is on the server.
  B. Verify that the client certificates are from the proper CA and server certificate.

• Question 129:

  You have a single Cisco 5508 WLC with a management IP address of 172.16.24.5/24. You need to register 50 new Cisco AIR-CAP3702I-E-K9. Access Points to the WLC using DHCP option 43. The access points are connected to a switch in VLAN 37, which uses the 172.16.37.0/24 subnet. You have configured the DHCP scope on the switch like this:

  Network 172.16.37.0 255.255.255.0 Default Router 172.16.37.1 Option 43 Aseii 172.16.24.5

  The access points are failing to join the wireless LAN controller. Which command fixes the issue?

  A. Option 43 Hex F108.CA10.1805
  B. Option 43 Hex F104.AC10.1705
  C. Option 43 Hex F112.CA10.1805
  D. Option 43 Hex F104.AC10.1805
  D. Option 43 Hex F104.AC10.1805

• Question 130:

  You have successfully configured HA and SSO using two Cisco 5508 Wireless LAN Controllers. You are able to access the Active Primary WLC but are unable to access the Secondary Standby WLC. Which two methods will allow you to access the standby unit? (Choose two.)

  A. Via SSH to the Redundancy Management Interface.
  B. Via Service Port Interface.
  C. Via SSH to the Management Interface.
  D. Via console connection.
  C. Via SSH to the Management Interface.
  D. Via console connection.