Cisco 300-360 Online Practice Questions and Exam Preparation

Cisco 300-360 Online Questions & Answers

• Question 31:

  Which three reasons describe the importance of assessing existing wired infrastructure when designing a new wireless network? (Choose three.)

  A. determine cable length
  B. determine port bandwidth
  C. determine CAPWAP support
  D. determine PoE requirement
  E. determine quality of service
  F. determine UPS requirement
  A. determine cable length
  B. determine port bandwidth
  D. determine PoE requirement

• Question 32:

  Refer to the exhibit. Which type of cable connector is displayed that is used to connect antennas to transmitters?

  

  A. RP-TNC
  B. N
  C. SMA
  D. SMB
  E. MMCX
  B. N

• Question 33:

  Which design limitation of dual-band WLAN must be considered when end-user devices stream real-time applications and services utilizing dual-band SSID?

  A. It can cause packet loss in the real-time path
  B. It can cause jitter and degrade overall network throughput
  C. It can cause short-term signal loss from collisions
  D. It can cause gaps in the real-time traffic path
  D. It can cause gaps in the real-time traffic path

• Question 34:

  Which two settings are dependent upon the regulatory domain in which an access point is installed? (Choose two.)

  A. AP mode
  B. frequency
  C. power
  D. IP address
  E. domain name
  D. IP address
  E. domain name

• Question 35:

  A post-deployment active wireless site survey was just completed for a company. Which two pieces of information must be included in the site survey report? (Choose two.)

  A. client performance metrics obtained during the survey
  B. heat maps from the data that was captured
  C. floor plans for Cisco Prime Infrastructure
  D. existing WLC configurations
  E. RRM recommendations for the WLC
  B. heat maps from the data that was captured
  D. existing WLC configurations

• Question 36:

  Which two pieces of physical infrastructure information should be included in the installation report presented to the customer? (Choose two.)

  A. A list of router and switch models, serial numbers and locations.
  B. The total square footage of the customer's facility.
  C. An analysis of the facility exterior wall and roof construction materials.
  D. The cable scan results for the entire customer facility.
  E. An installation inventory of all controllers and APs in the WLAN coverage area.
  D. The cable scan results for the entire customer facility.
  E. An installation inventory of all controllers and APs in the WLAN coverage area.

• Question 37:

  An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best 802.11n client compatibility?

  A. UNII-2
  B. UNII-2e
  C. UNII-3
  D. UNII
  E. UNII-1
  E. UNII-1

  ---

  802.11n operates on the same channel as 802.11a. For better compatibility with 802.11n clients, it is recommended to stay on lower channels (UNII-1 band). Reference: http://www.cisco.com/c/en/us/support/docs/wireless/4400-serieswireless-lan-controllers/108184-config-802-11n-wlc.html

• Question 38:

  You must configure IPv6 to drop unwanted or rogue RA packets that come from wireless clients. Which feature do you enable?

  A. RA throttling
  B. DHCPv6 Server Guard
  C. IPv6 Source Guard
  D. RA guard
  D. RA guard

• Question 39:

  The ClO of a company wants to start tracking inventory in the warehouse using RFID tags and their existing wireless network.

  The company hires a wireless engineer to ensure that their existing network can support this new initiative. Which tool in the Cisco Prime Infrastructure can you use to identify whether an existing network can support RFID tags?

  A. Planning Mode
  B. Voice Readiness
  C. Site Survey
  D. Location Readiness
  D. Location Readiness

• Question 40:

  What is the average IP packet loss needed to support real-time application over a wireless network?

  A. more than 2%
  B. less than or equal to 1%
  C. less than 10%
  D. between 2% and 5%
  B. less than or equal to 1%