Cisco 300-165 Online Practice Questions and Exam Preparation

Cisco 300-165 Online Questions & Answers

• Question 131:

  Which SCSI terminology is used to describe source and destination nodes?

  A. hosts and targets
  B. initiators and targets
  C. HBA and disks
  D. initiators and disks
  E. HBA and targets
  B. initiators and targets

  ---

  In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a SCSI command. The initiator usually does not provide any Logical Unit Numbers (LUNs). On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible. http://en.wikipedia.org/wiki/SCSI_initiator_and_target

• Question 132:

  On a Cisco Catalyst 6500 Series Supervisor Engine 720, an aggregate policer can be applied on which three of these? (Choose three.)

  A. an IP subnet
  B. a module with a DFC
  C. a fabric channel interface
  D. a port
  E. a VLAN
  F. a group of VLANs
  D. a port
  E. a VLAN
  F. a group of VLANs

• Question 133:

  

  Refer to the exhibit. Which result of implementing the configuration is true?

  A. Full vEthernet profile configurations are passed to the vNIC of the server.
  B. The native VLAN on the BACKUP port profile is available.
  C. Ethernet 1/5 is configured to pass VNTag traffic.
  D. Only vEthernet profile names are passed to the vNIC of the server.
  D. Only vEthernet profile names are passed to the vNIC of the server.

  ---

  Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/adapter-fex/6x/b_5500_Adapter_FEX_Config_6x/b_5500_Adapter_FEX_Config_602N11_chapter_010.html

• Question 134:

  Which two statements are true when configuring a port-channel between two Cisco Nexus 7000 Series switches? (Choose two.)

  A. You can combine Layer 2 and Layer 3 interfaces in the same port channel.
  B. You can configure a shared interface to be part of a port channel.
  C. A port may belong to more than one port channel.
  D. All ports in the port channel must be in the same VDC
  E. Ports must be of the same module type.
  D. All ports in the port channel must be in the same VDC
  E. Ports must be of the same module type.

  ---

  Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/interfaces/configuration/guide/if_cli/if_portchannel.pdf

• Question 135:

  Which two RFCs are supported by Cisco NX-OS devices for OSPFv2? (Choose two.)

  A. RFC 2238
  B. RFC 1918
  C. RFC 1583
  D. RFC 2453
  E. RFC 2740
  A. RFC 2238
  C. RFC 1583

• Question 136:

  

  Refer to the exhibit. Which result of implementing the configuration is true?

  A. The VLAN is spanned in the Rx and Tx directions.
  B. VLAN 2 can be used in another session.
  C. The SPAN session is localized.
  D. Traffic from 10.0.0.62 is captured.
  D. Traffic from 10.0.0.62 is captured.

• Question 137:

  Which statement about enhanced zoning on Cisco Multilayer Director Switches is true?

  A. Zone changes can scheduled with a CRON job.
  B. It allows patial zone set changes to be distributed without having to active a zone set.
  C. Enhanced zoning is compatible with IVR.
  D. More than one zone set can be active wit enhanced zoning.
  B. It allows patial zone set changes to be distributed without having to active a zone set.

• Question 138:

  Which statement about vPC loop avoidance is true?

  A. Up to four peer devices can be part of the same vPC domain.
  B. Traffic that comes from a vPC member port, and then crosses a vPC peer link, can leave through any vPC member port.
  C. A vPC domain performs loop avoidance on the control plane layer
  D. A vPC domain performs loop avoidance on the data plane layer
  D. A vPC domain performs loop avoidance on the data plane layer

• Question 139:

  Refer to the exhibit. Which corrective action is taken to resolve the problem?

  

  A. Trunk four VLANs on interface ethernet 199/1/1.
  B. Use the shut and no shut interface ethernet 199/1/1so that the VLANs come up.
  C. Place interface ethernet 199/1/1 in VLAN 4 in the N5K-2 configuration.
  D. Prune all but four VLANs from vPC 199.
  E. Add VLAN 4 to vPC 199.
  C. Place interface ethernet 199/1/1 in VLAN 4 in the N5K-2 configuration.

  ---

  Place interface ethernet 199/1/1 in VLAN 4 in the N5K-2 configuration.

• Question 140:

  

  Refer to the exhibit. Which action do you take to prevent DAI from inspecting packets on Ethernet 2/0?

  A. Configure a DHCP snooping entry.
  B. Create a VLAN ACL.
  C. Create a MAC ACL.
  D. Configure Ethernet 2/0 as a trusted interface.
  D. Configure Ethernet 2/0 as a trusted interface.