Cisco 300-165 Online Practice Questions and Exam Preparation

Cisco 300-165 Online Questions & Answers

• Question 1:

  Which option is supported when configuring a VACL?

  A. redirect to a SPAN destination port
  B. log of traffic that is matched by a VACL by using a MAC ACL
  C. egress VACL that contains decapsulated VXLAN traffic
  D. access map entry that uses an IP or MAC ACL
  A. redirect to a SPAN destination port

• Question 2:

  When implementing VLAN 10 on multiple Cisco Nexus 5600 Series, which configuration is required to ensure that the full zone set and the active zone set are the same across the fabric?

  A. switch(config)# zoneset activate name ZONE10 vsan 10
  B. switch(config)# zoneset distribute full vsan 10
  C. switch(config)# zoneset distribute vsan 33
  D. switch(config)# zone-attribute-group name ATTR1 vsan 10
  E. switch(config-attribute-group)# broadcast
  A. switch(config)# zoneset activate name ZONE10 vsan 10

• Question 3:

  

  Refer to the exhibit. Link 1 from the DCI is overutilized. Which action do you take to resolve the issue?

  A. Assign a secondary address to the port-channel5 interface.
  B. Configure multiple overlay networks between the edge devices.
  C. Change the OSPF network type to broadcast.
  D. Change the port-channel load balancing method to adaptive.
  D. Change the port-channel load balancing method to adaptive.

• Question 4:

  Which action causes a Cisco Nexus switch to generate a system checkpoint automatically?

  A. disabling a currently enabled feature
  B. adding a new license to the switch
  C. creating a new VRF
  D. creating a new VDC
  A. disabling a currently enabled feature

• Question 5:

  

  Refer to the exhibit. Which impact of the configuration on VLAN 100 is true?

  A. The spanning tree cost value for VLAN 200 is 4.
  B. The maximum number of hops between hosts is 3.
  C. The maximum number of hops between hosts is 4.
  D. The spanning tree cost value for VLAN 100 is 65535.
  B. The maximum number of hops between hosts is 3.

• Question 6:

  

  Refer to the exhibit. Which statement about the configuration is true?

  A. The emulated switch ID is S30.
  B. The vPC+ domain ID must match on S30.
  C. The peer link is a FabricPath edge port.
  D. Packets to MAC A are using S100.
  A. The emulated switch ID is S30.

• Question 7:

  You have two switches that have an ISL between them and use a SAN port channel. One of the switches is configured to use active mode. To which mode can you configure the peer switch to ensure that the SAN port channel is functional?

  A. active or passive
  B. active or on
  C. active or F
  D. passive or E
  A. active or passive

• Question 8:

  You are troubleshooting the SAN fabric. You must find the FCID to WWPN mapping for the N ports of a Cisco MDS Series switch. Which two commands can you run? (Choose two.)

  A. show flogi database
  B. show vsan
  C. show fcip summary
  D. show fcns database
  E. show fspf database
  A. show flogi database
  D. show fcns database

• Question 9:

  Which should you run to configure HSRP on a Cisco Nexus 7000 Series switch?

  A. feature-set hsrp interface vlan100 ip address 10.1.1.1 255.255.255.0 hsrp version 2 hsrp 100 ip 10.1.1.1
  B. interface vlan100 ip address 10.1.1.2 255.255.255.0 hsrp 100 ip 10.1.1.1
  C. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 hsrp 1000 ip 10.1.1.1
  D. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 hsrp version 2 hsrp 1000 ip 10.1.1.1
  C. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 hsrp 1000 ip 10.1.1.1

• Question 10:

  On a Cisco Nexus 5500 Series switch, what is the result of running the (config-if)# switchport mode vntag command?

  A. allows the connected FEX to assign each VM a dedicated vEthernet interface on the host switch
  B. allows the connected server to assign each VM a dedicated vEthernet interface on the host switch
  C. allows the connected server to assign each VM a dedicated Ethernet interface on the host switch
  D. allows the connected FEX to assign each VM a dedicated Ethernet interface on the host switch
  A. allows the connected FEX to assign each VM a dedicated vEthernet interface on the host switch