Cisco 300-101 Online Practice Questions and Exam Preparation

Cisco 300-101 Online Questions & Answers

• Question 941:

  Network engineer wants to configure logging to compile and send information to an external server

  A. Terminal
  B. Syslog
  C. Buffer
  D. Console
  B. Syslog

• Question 942:

  An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters:

  mac address C601.420F.0007

  subnet 2001:DB8:0:1::/64

  Which IPv6 addresses should the engineer add to the documentation?

  A. 2001:DB8:0:1:C601:42FF:FE0F:7
  B. 2001:DB8:0:1:FFFF:C601:420F:7
  C. 2001:DB8:0:1:FE80:C601:420F:7
  D. 2001:DB8:0:1:C601:42FE:800F:7
  A. 2001:DB8:0:1:C601:42FF:FE0F:7

• Question 943:

  Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?

  A. ipv6 traffic-filter
  B. ipv6 access-list
  C. access-list ipv6
  D. ipv6 access-group
  A. ipv6 traffic-filter

• Question 944:

  What is the difference between the IPv6 addresses ::/0 and ::/128?

  A. ::/0 is the unspecified address, and ::/128 is the multicast address
  B. ::/0 is the unicast address, and ::/128 is the anycast address.
  C. ::/0 is the unicast address, and ::/128 is the multicast address.
  D. ::/0 is the anycast address, and ::/128 is the multicast address.
  E. ::/0 is the default route, and ::/128 is the unspecified address
  F. ::/0 is the anycast address, and ::/128 is the default address.
  E. ::/0 is the default route, and ::/128 is the unspecified address

• Question 945:

  Your network consists of a large hub-and-spoke Frame Relay network with a CIR of 56 kb/s for each spoke.Which statement about the selection of a dynamic protocol is true?

  A. EIGRP would be appropriate if LMI type ANSI is NOT used.
  B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas
  C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.
  D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
  D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.

• Question 946:

  What following parameters for the EIGRP authentication need to match in order for EIGRP neighbors to establish a neighbor relationship?

  A. Autonomous System number.
  B. K-Values
  C. If authentication is used both: the key number, the password, and the date/time.
  D. The neighbors must be on common subnet (all IGPs follow this rule).
  C. If authentication is used both: the key number, the password, and the date/time.

• Question 947:

  What is the optimal location from which to execute a debug command that produces an excessive amount of information?

  A. Vty lines
  B. SNMP commands
  C. A console port
  D. An AUX port
  A. Vty lines

• Question 948:

  Refer to the following Logging Console7 Which option is one of the effects entering this command on a Cisco IOS router, with no additional logging configuration?

  A. Debug messages can be seen on the console by enabling "terminal monitor."
  B. Debug messages are logged only on active console connections.
  C. A user that is connected via SSH sees level 7 messages
  D. The router can experience high CPU utilization
  B. Debug messages are logged only on active console connections.

• Question 949:

  Which IPv6 address correctly compresses the IPv6 unicast address 2001:0:0:0:0DB8:0:0:417A?

  A. 2001:0DB8:417A
  B. 2001::0DB8::417A
  C. 2001:::0DB8::417A D. 2001:0DB8:0:0:417A
  E. 2001::DB8:0:0:417A
  F. 2001:::0DB8:0:0:417A
  E. 2001::DB8:0:0:417A

• Question 950:

  Where the output will be shown of the command debug condition interface fa0/1 ?

  A. it will show on interface f0/1
  B. it will show on interface f0/0
  C. both interfaces will show debugging ouput
  D. an interface cannot be used as condition
  A. it will show on interface f0/1