Cisco 300-101 Online Practice Questions and Exam Preparation

Cisco 300-101 Online Questions & Answers

• Question 731:

  What command would you use to set EIGRP routes to be prioritized?

  A. distance 100
  B. distance 89
  C. distance eigrp 100
  D. distance eigrp 89
  D. distance eigrp 89

• Question 732:

  Which two authentication protocols does PPP support? (Choose two.)

  A. WAP
  B. PAP
  C. CHAP
  D. EAP
  E. RADIUS
  B. PAP
  C. CHAP

• Question 733:

  What from the following can cause an issue for URPF?

  OR

  Reasons why urpf may fail:

  A. Assymetrcfasic routing
  B. Cef not enabled
  C. Urpf not applied to the traffic source
  D. If it is usedas ingress filtering
  A. Assymetrcfasic routing

• Question 734:

  Which two steps must you perform to allow access to a device when the connection to a remote TACACS+ authentication server fails? (Choose two)

  A. Include the local keyword in the AAA configuration
  B. Configure a local username and password on the device
  C. Configure the device to accept Telnet and SSH connections
  D. Configure accounting to reference the log of previously authenticated connections
  E. Remove the aaa new model command from the gloabl configuration
  A. Include the local keyword in the AAA configuration
  B. Configure a local username and password on the device

• Question 735:

  A network administrator is attempting to configure IP SLA to allow one time stamp to be logged when a packet arrives on the interface and one time stamp to be logged when a packet leaves the interface. Which IP SLA accuracy tool enables this functionality?

  A. Trap
  B. RTT
  C. Responder
  D. Trigger
  C. Responder

• Question 736:

  Refer to the exhibit. Which option prevents routing updates from being sent to the DHCP router, while still allowing routing update messages to flow to the Internet router and the distribution switches?

  

  A. CORE(config)# access-list ... deny CORE(config)# access-list ... permit CORE(config-router)# distribute-list .. out
  B. CORE(config)# access-list ... deny CORE(config)# access-list ... permit CORE(config-if)# distribute-list .. out
  C. DHCP(config)# access-list ... deny DHCP(config)# access-list ... permit CORE(config-router)# distribute-list .. out
  D. CORE(config)# access-list ... deny CORE(config)# access-list ... permit DHCP(config-if)# distribute-list .. out
  A. CORE(config)# access-list ... deny CORE(config)# access-list ... permit CORE(config-router)# distribute-list .. out

• Question 737:

  Which value identifies traffic intended for different paths in an EVN environment?

  A. VLAN ID
  B. route target
  C. route tag
  D. VNET tag
  D. VNET tag

• Question 738:

  Refer to the exhibit.

  

  A network engineer is troubleshooting a DMVPN setup between the hub and the spoke.

  The engineer executes the command show crypto isakmp sa and observes the output that is displayed. What is the problem?

  A. That ISAKMP is not enabled
  B. That ISAKMP is using default settings
  C. An incompatible IP sec transform set
  D. An incompatible ISAKMP policy
  B. That ISAKMP is using default settings

• Question 739:

  Which feature or technology is supported with stateful NAT64 ?

  A. IP multicast
  B. NAT44 and NAT64 on the same interface
  C. VFR
  D. FTP and ICMP on an application layer gateway
  C. VFR

• Question 740:

  Which two statements are examples of the differences between IPv4 and IPv6 EIGRP? (Choose two.)

  A. Network command is used in IPv6
  B. DUAL is not used for route calculations.
  C. DUAL is used for route calculations
  D. IPv6 keyword is used in many EIGRP commands.
  E. Network command is not used in IPv6
  D. IPv6 keyword is used in many EIGRP commands.
  E. Network command is not used in IPv6