Cisco 200-355 Online Practice Questions and Exam Preparation

Cisco 200-355 Online Questions & Answers

• Question 441:

  A wireless engineer is troubleshooting an RF issue. Which device in the lightweight WLAN architecture is responsible for RF management?

  A. Prime Infrastructure
  B. WLC
  C. Lightweight access point
  D. MSE
  B. WLC

• Question 442:

  An engineer needs an AP with at least two spatial streams, four receivers, and three transmitters. Which device meets these requirements?

  A. 2x4:3
  B. 2x3:4
  C. 4x3:2
  D. 3x4:2
  D. 3x4:2

• Question 443:

  You are setting up a laptop to connect to the wireless network of your organization. The protocols that are used for the corporate network are WPA2 Enterprise, PEAP, and AES. Which three parameters do you need to configure in the Windows 7 wireless network properties for this connection? (Choose three.)

  A. VLAN
  B. encryption type
  C. authentication method
  D. VRF
  E. security type
  F. IP address
  B. encryption type
  C. authentication method
  E. security type

  ---

  On the Security tab, you can specify the following security types:

  Based on the selected security type, you can configure either a network security key or specify and configure a network authentication method. If you specify WPA-Enterprise, WPA2-Enterprise, or 802.1x as your security type, you must

  configure the following (as shown in the previous figure):

  1.

  Choose a network authentication methodSelect an Extensible Authentication Protocol (EAP) method and click Settings to configure the EAP type as needed.

  2.

  Remember my credentials for this connection each time I'm logged on: Specifies that when the user logs off, the user credential data is not removed from the registry. If you clear the checkbox, the next time the user logs on, he will be prompted for credentials (such as user name and password).

  If you specify the use of WPA-Personal or WPA2-Personal as your security type or No authentication (Open) or Shared as your security type with WEP as your encryption type, you must configure a network security key, as shown in Figure: https://technet.microsoft.com/en-us/magazine/ff847520.aspx

  

• Question 444:

  What is the maximum number of access points supported on Cisco WCS with an enterprise license?

  A. 5,000
  B. 10,000
  C. 50,000
  D. 100,000
  C. 50,000

  ---

  http://www.cisco.com/c/en/us/products/collateral/wireless/wireless-control-system/product_data_sheet0900aecd804b4646.html

• Question 445:

  How much wireless cell overlapping is required for 5GHz voice and data roaming?

  A. 5%
  B. 10%
  C. 15%
  D. 20%
  D. 20%

• Question 446:

  What tab contains access point configuration in the WCS?

  A. Controller > Access Points
  B. Configure > Access Points
  C. General > Configure > Access Points
  D. System > Configure > Access Points
  B. Configure > Access Points

• Question 447:

  Refer to the exhibit.

  

  Which two wireless functions is the client experiencing? (Choose two.)

  A. Inter-controller Roaming
  B. Intra-controller Roaming
  C. Layer 2 Roaming
  D. Layer 3 Roaming
  E. Inter-subnet roaming
  F. Re-authentication
  B. Intra-controller Roaming
  C. Layer 2 Roaming

• Question 448:

  What is the approximate time difference for a client to perform an intracontroller roam compared to an intercontroller roam?

  A. 1 ms
  B. 10 ms
  C. 20 ms
  D. 30 ms
  B. 10 ms

• Question 449:

  Which two statements about the requirements to configure intercontroller roaming are true? (Choose two.)

  A. The same AP manager interface is configured across controllers.
  B. The same mobility domain names are configured across controllers.
  C. The same RF group names are configured across controllers.
  D. The same virtual interface is configured across controllers.
  E. The same controller hardware version is configured across controllers.
  B. The same mobility domain names are configured across controllers.
  D. The same virtual interface is configured across controllers.

• Question 450:

  Which command is used to upgrade the operational code when upgrading a Cisco IOS-XE WLC?

  A. software install source switch
  B. software install file path:code.bin
  C. software tftp://code.bin flash:/code.bin
  D. software expand running
  B. software install file path:code.bin