Cisco 200-125 Online Practice Questions and Exam Preparation

Cisco 200-125 Online Questions & Answers

• Question 581:

  Which option describes a benefit of a point-to-point leased line?

  A. full-mesh capability
  B. flexibility of design
  C. low cost
  D. simplicity of configuration
  D. simplicity of configuration

• Question 582:

  which two pieces of information can you learn by viewing the routing table?(choose two)

  A. whether access list are blocking incoming routes
  B. the interface on which traffic is send
  C. whether a route was learned via IGP or EGP
  D. whether routes were summarized
  E. whether a route was tagged
  B. the interface on which traffic is send
  C. whether a route was learned via IGP or EGP

• Question 583:

  A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?

  A. This is a 10 Mb/s switch port.
  B. This is a 100 Mb/s switch port.
  C. This is an Ethernet port operating at half duplex.
  D. This is an Ethernet port operating at full duplex.
  E. This is a port on a network interface card in a PC.
  C. This is an Ethernet port operating at half duplex.

  ---

  Modern Ethernet networks built with switches and full-duplex connections no longer utilize CSMA/CD. CSMA/CD is only used in obsolete shared media Ethernet (which uses repeater or hub).

• Question 584:

  Which technology can enable multiple VLANs to communicate with one another?

  A. inter-VLAN routing using a Layer 3 switch
  B. inter-VLAN routing using a Layer 2 switch
  C. intra-VLAN routing using router on a stick
  D. intra-VLAN routing using a Layer 3 switch
  A. inter-VLAN routing using a Layer 3 switch

• Question 585:

  Which command should you enter to configure a device as an NTP sever?

  A. ntp peer
  B. ntp authenticate
  C. ntp sever
  D. ntp master
  D. ntp master

  ---

  https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/system_management/503_n1_1/b_cisco_n5k_system_mgmt_cg_rel_503_n1_1/ b_cisco_n5k_system_mgmt_cg_rel_503_n1_1_chapter_010000.pdf

• Question 586:

  

  Which command must you enter to configure a DHCP relay?

  A. ip helper-address
  B. ip address dhcp
  C. ip dhcp relay
  D. ip dhcp pool
  A. ip helper-address

• Question 587:

  You apply a new inbound access list to routers, blocking UDP packets to the HSRP group. Which two effects does this action have on HSRP group process? (Choose two )

  A. HSRP redundancy works as expected.
  B. HSRP redundancy fails
  C. The active router immediately becomes the standby router
  D. Both the active and standby routers become active
  E. The routers in the group generate duplicate IP address warnings
  B. HSRP redundancy fails
  D. Both the active and standby routers become active

• Question 588:

  Drag each IPv6 prefix on the left to its use on the right.

  Select and Place:

  

  

  ---

  FF02::1 = All link-local nodes on a segment FF02::5 = all OSPFv3 routers FF02::6 = OSPFv3 designated routers FF02::A = all EIGRPv6 routers FF02::D = All PIM routers FF05::2 = all site local routers

• Question 589:

  Which two pieces of information can you determine from the EIGRP topology table? (Choose two)

  A. Route 10.42.88.0/21 has an administrative distance of 28160
  B. Route 10.42.91.0/24 has a tag of 28160
  C. Each route has only one best path
  D. The EIGRP neighbor IP address is 10.111 253.216
  E. The reported distance of 10.0.0.0/8 is 0
  C. Each route has only one best path
  E. The reported distance of 10.0.0.0/8 is 0

• Question 590:

  Which feature builds a FIB and an adjacency table to expedite packet forwarding?

  A. Cisco Express Forwarding
  B. process switching
  C. fast switching
  D. cut-through
  A. Cisco Express Forwarding