Cisco 200-105 Online Practice Questions and Exam Preparation

Cisco 200-105 Online Questions & Answers

• Question 161:

  Which two protocols can detect native vlan mismatch errors? (Choose two.)

  A. STP
  B. Cisco Discovery Protocol
  C. VTP
  D. DTP
  E. PAgP
  B. Cisco Discovery Protocol
  C. VTP

• Question 162:

  Refer to the exhibit. Which two statements about the configuration of the switch interface are correct? (Choose two.)

  

  A. The switchport belongs only to VLAN 2.
  B. By default, all switch ports are members of VLAN 1005.
  C. Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2.
  D. The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2.
  E. A network host can be connected to this interface.
  A. The switchport belongs only to VLAN 2.
  E. A network host can be connected to this interface.

• Question 163:

  Refer to the exhibit.

  A network associate has configured OSPF with the command:

  City(config-router)# network 192.168.12.64 0.0.0.63 area 0

  After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose

  three.)

  

  A. FastEthernet0 /0
  B. FastEthernet0 /1
  C. Serial0/0
  D. Serial0/1.102
  E. Serial0/1.103
  F. Serial0/1.104
  B. FastEthernet0 /1
  C. Serial0/0
  D. Serial0/1.102

  ---

  The "network 192.168.12.64 0.0.0.63 equals to network 192.168.12.64/26. This network has:

  Increment: 64 (/26= 1111 1111.1111 1111.1111 1111.1100 0000) Network address:192.168.12.64

  Broadcast address: 192.168.12.127Therefore all interface in the range of this network will join OSPF -B C D are correct.

• Question 164:

  What command sequence will configure a router to run OSPF and to add network 10.1.1.0/24 to area 0?

  A. router ospf network 10.1.1.0 0.0.0.255
  B. router ospf 1 network 10.1.1.0 0.0.0.255
  C. router ospf network 10.1.1.0 255.255.255.0 area 0
  D. router ospf 1 network 10.1.1.0 0.0.0.255 area 0
  E. router ospf area 0 network 10.1.1.0 255.255.255.0 area 0
  F. router ospf area 0 network 10.1.1.0 0.0.0.255 area 0
  D. router ospf 1 network 10.1.1.0 0.0.0.255 area 0

• Question 165:

  Which channel group mode must you configure on both ports to enable a static EtherChannel?

  A. auto
  B. passive
  C. active
  D. desirable
  E. on
  E. on

• Question 166:

  Which command shows your active Telnet connections?

  A. show cdp neigbors
  B. show session
  C. show users
  D. show vty logins
  B. show session

• Question 167:

  DRAG DROP

  Drag and drop the trunking terms from the left onto the correct descriptions on the right.

  Select and Place:

  

  

• Question 168:

  What is the alert message generated by SNMP agents called? (Choose two.)

  A. TRAP
  B. INFORM
  C. GET
  D. SET
  A. TRAP
  B. INFORM

• Question 169:

  DRAG DROP

  Drag and drop the DHCP snooping terms from the left onto the correct descriptions on the right.

  Select and Place:

  

  

• Question 170:

  Which statement about OSPFv3 configuration is true?

  A. You can add networks under the routing process.
  B. You must configure neighbors manually.
  C. You must individually add interface IP addresses to the OSPFv3 database.
  D. You can enable OSPFv3 for a network under the interface configuration mode.
  D. You can enable OSPFv3 for a network under the interface configuration mode.