Cisco 200-105 Online Practice Questions and Exam Preparation

Cisco 200-105 Online Questions & Answers

• Question 131:

  Which technology supports multiple dynamic secure connections an unsecure transport network?

  A. DMVPN
  B. VPN
  C. Site-to-site VPN
  D. client VPN
  A. DMVPN

• Question 132:

  Which two values can a standard IPv6 ACL use to identify traffic? (Choose two.)

  A. UDP header
  B. TCP header
  C. source IPv6 address
  D. DSCP value for QoS
  E. destination IPv6 address
  C. source IPv6 address
  E. destination IPv6 address

• Question 133:

  Which two traffic types must always be transmitted on VLAN 1? (Choose two.)

  A. UDP
  B. DTP
  C. NTP
  D. CDP
  E. TCP
  B. DTP
  D. CDP

• Question 134:

  What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

  A. 2
  B. 4
  C. 16
  D. unlimited
  B. 4

  ---

  4 is the default number of routes that OSPF will include in routing table if more than 4 equal cost routes exist for the same subnet. However, OSPF can include up to 16 equal cost routes in the routing table and perform load balancing amongst them. In order to configure this feature, you need to use the OSPF subcommand maximum-paths, i.e. maximum-paths 16.

• Question 135:

  Which information is provided by the output of the show snmp engineID command?

  A. Information about remote SNMP engines on the network only.
  B. Information about the local SNMP engine and remote SNMP engines that are configured on the device.
  C. Information about SNMP users and SNMP groups in the network.
  D. Information about the local SNMP engine only.
  B. Information about the local SNMP engine and remote SNMP engines that are configured on the device.

• Question 136:

  Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)

  A. Router(config)# router ospf 0
  B. Router(config)# router ospf 1
  C. Router(config)# router ospf area 0
  D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
  E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
  F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
  B. Router(config)# router ospf 1
  E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0

  ---

  In the router ospf command, the ranges from 1 to 65535 so o is an invalid number -B is correct but A is not correct.

  To configure OSPF, we need a wildcard in the "network" statement, not a subnet mask. We also need to assign an area to this process -E is correct.

• Question 137:

  Which command enables IPv6 forwarding on a Cisco router?

  A. ipv6 local
  B. ipv6 host
  C. ipv6 unicast-routing
  D. ipv6 neighbor
  C. ipv6 unicast-routing

  ---

  The first step of enabling IPv6 on a Cisco router is the activation of IPv6 traffic forwarding to forward unicast IPv6 packets between network interfaces. By default, IPv6 traffic forwarding is disabled on Cisco routers. The ipv6 unicast-routing command is used to enable the forwarding of IPv6 packets between interfaces on the router. The syntax for this command is as follows: Router(config)#ipv6 unicast-routing The ipv6 unicast-routing command is enabled on a global basis. Reference: http://www.ciscopress.com/articles/article.asp?p=31948andseqNum=4

• Question 138:

  What happens when you execute the APIC-EM ACL path trace feature and it fails to discover a matching ACE along the path?

  A. The ACLs along the path block the path trace attempt.
  B. The feature reports the flow as implicitly denied.
  C. The feature aborts the path trace.
  D. The feature flags all possible ACE entries as invalid.
  B. The feature reports the flow as implicitly denied.

  ---

  Reference: https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/application-policy-infrastructure-controller-enterprise-module/1-6-x/path_trace/user-guide/b_Cisco_Path_Trace_User_Guide_1_6_0_x/ b_Cisco_Path_Trace_User_Guide_1_6_0_x_chapter_0111.html

• Question 139:

  Which two statements about CHAP are true? (Choose two.)

  A. The CHAP negotiation phase begins after the LCP phase is complete.
  B. Each authenticating router has a unique username and password.
  C. It uses a three-way handshake to identify the peer router.
  D. The local MD5 secret is transmitted to the peer for authentication.
  E. The LCP phase begins after CHAP authentication is complete.
  A. The CHAP negotiation phase begins after the LCP phase is complete.
  C. It uses a three-way handshake to identify the peer router.

• Question 140:

  Which statement about snmpv2 is true?

  A. it requires password at least eight characters in length
  B. it requires passwords to be encrypted
  C. its privacy algorithms use md5 encryption by default
  D. its authentic and privacy algorithms are enabled without default values
  D. its authentic and privacy algorithms are enabled without default values