Riverbed 199-01 Online Practice Questions and Exam Preparation

Riverbed 199-01 Online Questions & Answers

• Question 51:

  Connection Pooling works with:

  A. Port and Full Transparency
  B. Correct Addressing and Port Transparency
  C. Correct Addressing only
  D. Correct Addressing, Port and Full Transparency
  E. Full Transparency only
  D. Correct Addressing, Port and Full Transparency

• Question 52:

  In order to reset the admin password that has been lost, the procedure can be done via what type of connection to a Steelhead appliance?

  A. SSH over Primary interface IP
  B. SSH over AUX interface IP
  C. SSH over in-path interface IP
  D. Serial cable connection
  E. Password recovery can not be done on a Steelhead appliance
  D. Serial cable connection

• Question 53:

  The IP address for which neighbor interface should be configured for Connection Forwarding? 1) lan0_0 2) inpath0_0 3) Primary 4) AUX 5) inpath7_7

  B. 2
  C. 1, 5
  D. 2, 3, 4, 5
  E. 1, 2, 3, 4, 5
  B. 2

• Question 54:

  Refer to the exhibit.

  

  What does the term resyncing mean?

  A. All Interceptor appliances have been connected and the appliances are transferring connection information
  B. All Interceptor appliances and all Steelhead appliances have been connected and the appliances are transferring connection information
  C. The connection has been established and the Interceptor appliance is transferring its state information
  D. The connection has been established and the devices are transferring their state information
  D. The connection has been established and the devices are transferring their state information

• Question 55:

  When using Correct Addressing, without Enhanced Auto-discovery (EAD), what is the size of the probe response in the return SYN/ACK packet from the server-side Steelhead appliance?

  A. 4 bytes
  B. 10 bytes
  C. 14 bytes
  D. 18 bytes
  E. 32 bytes
  C. 14 bytes

• Question 56:

  -- Exhibit

  

  -- Exhibit -Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, it was observed that the returning traffic from Server2 is not being optimized by the Steelhead appliances. Why? (Select 2)

  A. The router is not properly configured.
  B. Physical in-path mode should be enabled.
  C. The wccp redirect command is missing.
  D. You should disable logical in-path.
  A. The router is not properly configured.
  C. The wccp redirect command is missing.

• Question 57:

  Up to how many TCP connections can the Interceptor 9600 handle?

  A. 1,000,000
  B. 1,500,000
  C. 2,000,000
  D. 2,500,000
  E. 3,000,000
  A. 1,000,000

• Question 58:

  The picture below corresponds to a connection using the SteelHead SaaS GeoDNS feature. What is the IP address of the closest Microsoft Exchange Client Access Server (CAS)?

  

  A. 132.245.24.82
  B. 172.16.38.222
  C. Not enough information. You would need the output of show service cloud geodns
  D. 132.245.92.226
  D. 132.245.92.226

• Question 59:

  Which of the following commands would allow you to generate a system dump from the CLI?

  A. sysdump
  B. dump generate
  C. debug generate dump
  D. sysdump generate dump
  E. dump generate -w filename
  C. debug generate dump

• Question 60:

  Refer to the exhibit.

  

  A connection times out when Client41 and Client42 attempt to either establish an HTTP session to Server31 or an FTP connection to Server32 after not connecting to them for some time. The very next attempt to connect to these services done immediately after the failure seems to work correctly. The clients are able to ping both servers and no access-lists are configured on the routers. SH3 uses the IP address of R3f0 as its default gateway. Upon powering off SH3 and SH4, the problem goes away even for first connection and everything works normally (even after not connecting for extended periods of time). Which of the following are likely to correct this problem?

  A. Both servers have faulty network interface cards and should be replaced
  B. Both the HTTP service running in Server31 and the FTP service running in Server32 are down and should be restarted
  C. A more specific static route pointing to Subnet 31 is not configured at SH3
  D. A more specific static route pointing to Subnet 31 is not configured at R3
  E. A more specific static route pointing to Subnet 31 is not configured at L3 Switch
  C. A more specific static route pointing to Subnet 31 is not configured at SH3