Riverbed 199-01 Online Practice Questions and Exam Preparation

Riverbed 199-01 Online Questions & Answers

• Question 71:

  You have a pair of SteelHead appliances, both deployed in-path, both have a valid IP address on the in-path interfaces, optimizations are enabled and the service is started. They are unable to auto discover each other as a firewall is stripping the probes. How could you work around this on the SteelHeads?

  A. Enable Enhanced Auto Discovery on each SteelHead and restart the optimization service.
  B. Create a full transparency in-path rule on each SteelHead.
  C. Use static NAT entries for each in-path interface.
  D. Create a fixed-target in-path rule on each SteelHead pointing to the peer in-path IP address on port 7810.
  E. Create a port transparency in-path rule on each SteelHead
  D. Create a fixed-target in-path rule on each SteelHead pointing to the peer in-path IP address on port 7810.

• Question 72:

  -- Exhibit -- Exhibit -

  

  Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Interceptor appliances, and the Steelhead appliance, he decided to check if the devices will work appropriately. According to the information shown, what statements are true? (Select 2)

  A. There are two Interceptor appliances: 172.16.19.111 and 172.16.19.112 in parallel mode, and one Steelhed appliance. 172.16.10.101.
  B. There are two Interceptor appliances: 172.16.19.111 and 172.16.19.112 in failover mode, and one Steelhead appliance. 172.16.10.101.
  C. This scenario should work appropriately and the devices are configured correctly.
  D. This scenario will only work if you add one more Steelhead appliance.
  B. There are two Interceptor appliances: 172.16.19.111 and 172.16.19.112 in failover mode, and one Steelhead appliance. 172.16.10.101.
  C. This scenario should work appropriately and the devices are configured correctly.

• Question 73:

  What type of reporting information will an Interceptor appliance store? (Select 2)

  A. Connection counts
  B. Total packets in and out
  C. Bytes and packets redirected to each neighbor Steelhead appliance
  D. Scalable Data Referencing (SDR) Status
  A. Connection counts
  B. Total packets in and out

• Question 74:

  What are the SSL trusts that must be configured for a Steelhead Mobile client to successfully optimize SSL traffic? (Select 2)

  A. Steelhead Mobile clients trust Steelhead Mobile Controller
  B. Server-side Steelhead trusts Steelhead Mobile clients
  C. Steelhead Mobile clients trusts client-side Steelhead
  D. Client-side Steelhead, server-side Steelhead, Steelhead Mobile clients, and CMC appliance all must trust each other
  A. Steelhead Mobile clients trust Steelhead Mobile Controller
  B. Server-side Steelhead trusts Steelhead Mobile clients

• Question 75:

  On the Steelhead Mobile Controller, what VPNs require the use of Reorder Intermediate Drivers? (Select 2)

  A. Nortel VPN
  B. Cisco VPN client
  C. Check Point
  D. OpenVPN
  E. Riverbed VPN client
  A. Nortel VPN
  C. Check Point

• Question 76:

  When configuring failover, in what manner must you configure your Steelhead appliances? 1) Master/Backup 2) Primary/Secondary/Tertiary 3) Master/Master 4) Backup/Backup 5) Primary/Principle

  A. 1
  B. 2
  C. 3, 4
  D. 1, 3, 4
  E. 1, 2, 3, 4, 5
  A. 1

• Question 77:

  If data store synchronization is to be successful, which of these must be true?

  A. There must be a resilient path between the SteelHeads to prevent a split brain situation.
  B. The in-path IP addresses must be reachable from each other and connected physically in-path.
  C. The SteelHeads must be the same model and run the same RiOS version.
  D. The master must be the same or larger data store than the backup.
  E. The SteelHeads must be in a serial cluster arrangement.
  B. The in-path IP addresses must be reachable from each other and connected physically in-path.

• Question 78:

  What is the command to view configuration files on the CLI?

  A. configuration files display
  B. configuration files view
  C. configuration files show
  D. show configuration files
  E. show configuration files all
  D. show configuration files

• Question 79:

  What CLI command is used to view logs?

  A. show log
  B. show debug logging enable
  C. show debug logs enable
  D. view debug generate dump
  E. view logs
  F. tail -f /var/logs
  A. show log

• Question 80:

  For a new connection, a Load Balancing rule matches but none of the target Steelhead appliances in the rule are available. What will happen to the new connection?

  A. The connection is passed through
  B. The next rule in the list is examined
  C. The Interceptor appliance triggers an alarm
  D. The Interceptor appliance discontinues redirecting any new connections and places this rule in admissions control
  B. The next rule in the list is examined