Riverbed 199-01 Online Practice Questions and Exam Preparation

Riverbed 199-01 Online Questions & Answers

• Question 391:

  On the Steelhead Mobile Controller, what is the default setting of Reorder Intermediate Drivers?

  A. Enabled
  B. Disabled
  C. Offline
  D. Online
  E. Checked
  B. Disabled

• Question 392:

  Which of the following is true regarding the CMC appliance?

  A. Can be configured using its default IP address of 192.168.1.1
  B. Can be initially set up via the CLI
  C. Can be initially setup via the AUX interface
  D. Can be initially set up via telnet
  E. Both C and D
  B. Can be initially set up via the CLI

• Question 393:

  When optimizing applications that open many short-lived HTTP connections, which operating mode will give the best performance?

  A. Full Transparency
  B. Full Transparency with reset
  C. Correct Addressing
  D. Port Transparency
  E. Any of the above, because performance is not affected by these
  C. Correct Addressing

• Question 394:

  What are the methods to upload an RSP package? (Select 3)

  A. tftp
  B. scp
  C. ftp
  D. ssh
  E. http
  B. scp
  C. ftp
  E. http

• Question 395:

  Which of the following points on WCCP v2 are correct? (Select 4)

  A. Intercept on outbound interface only
  B. Multicast support
  C. Able to redirect any TCP/UDP traffic
  D. Uses UDP port 2048 for control messages
  E. Multi-router support
  B. Multicast support
  C. Able to redirect any TCP/UDP traffic
  D. Uses UDP port 2048 for control messages
  E. Multi-router support

• Question 396:

  A recently installed branch SteelHead is successfully optimizing connections inbound from other locations. However, users report that their connections originating from that branch don't seem to be any faster and the Current Connections report shows their connections to be in pass-through. In-path rules correctly specify that auto-discovery should occur. What might be the problem?

  A. Simplified Routing should be enabled.
  B. There is asymmetry in the network.
  C. The optimization service on the branch SteelHead is not running.
  D. There is a duplex mismatch on the LAN port.
  E. The SteelHead LAN and WAN ports have been wired in reverse.
  E. The SteelHead LAN and WAN ports have been wired in reverse.

• Question 397:

  You would like to upgrade a Virtual SteelHead VCX755-L to VCX755-H. What is required to permit the upgrade to succeed? (Choose three.)

  A. Additional bypass cards
  B. Additional CPU(s)
  C. An upgrade license key
  D. Additional Storage capacity for data store
  E. Additional Memory
  C. An upgrade license key
  D. Additional Storage capacity for data store
  E. Additional Memory

• Question 398:

  What are the four types of policies on a CMC appliance?

  A. Networking, Optimization, Software, System
  B. Networking, Optimization, Rules, System
  C. Networking, Optimization, Security, System
  D. Networking, Acceleration, Security, System
  C. Networking, Optimization, Security, System

• Question 399:

  Peer affinity is most closely related to:

  A. Parallel Interceptor redirection based on Sport ID and client IP
  B. Serial Interceptor redirection based on Sport ID to server
  C. Segstore ID Steelhead mapping based on Sport ID of Steelhead appliances
  D. The shipyard from which Riverbed is most likely to ship Interceptors
  C. Segstore ID Steelhead mapping based on Sport ID of Steelhead appliances

• Question 400:

  Users report that CIFS transfer speeds from a domain member server are much faster than from a domain controller. The Current Connections report confirms that connections to the domain controller show a red warning triangle. What configuration steps are required to resolve this issue?

  A. Domain Controllers should not be used for file sharing as they are always slower than domain member servers.
  B. The server-side SteelHead should be joined to the domain in Workstation mode, enable CIFS SMB Signing and Transparent Mode.
  C. Both the client-side and server-side SteelHeads should be joined to the domain in Active Directory Integrated mode.
  D. The client-side SteelHead should be joined to the domain in Workstation mode, enable CIFS SMB Signing and Transparent Mode.
  E. The server-side SteelHead should be joined to the domain in Active Directory Integrated mode, enable CIFS SMB Signing and Transparent Mode.
  C. Both the client-side and server-side SteelHeads should be joined to the domain in Active Directory Integrated mode.