Cisco 100-105 Online Practice Questions and Exam Preparation

Cisco 100-105 Online Questions & Answers

• Question 521:

  DRAG DROP

  Drag and drop the routing protocols from the left onto the default administrative distances on the right.

  Select and Place:

  

  

• Question 522:

  Which two ACL types support IP Access List Entry Sequence Numbering? (Choose two.)

  A. named
  B. reflexive
  C. firewall
  D. dynamic
  E. standard
  A. named
  E. standard

• Question 523:

  

  To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.)

  A. R2(config-if)#clock rate
  B. R2(config-if)#bandwidth
  C. R2(config-if)#ip ospf cost
  D. R2(config-if)#ip ospf priority
  E. R2(config-router)#distance ospf
  B. R2(config-if)#bandwidth
  C. R2(config-if)#ip ospf cost

• Question 524:

  Which statement about RIPv2 is true?

  A. Unless the network command is issued under the routing process, all interfaces are passive by default.
  B. It is a classful routing protocol.
  C. Auto summary is disabled by default.
  D. The RIP routing protocol must be enabled on the router before RIPv2 is configured.
  A. Unless the network command is issued under the routing process, all interfaces are passive by default.

• Question 525:

  Which command can you enter to determine the addresses that have been assigned on a DHCP Server?

  A. Show ip DHCP database.
  B. Show ip DHCP pool.
  C. Show ip DHCP binding.
  D. Show ip DHCP server statistic.
  C. Show ip DHCP binding.

• Question 526:

  If you are in VLAN 10 and it gets a packet from VLAN 2 with 802.1q enabled, what does it do with the packet?

  A. Drops the packet
  B. forwards it to VLAN 2
  C. configures the port to handle traffic from VLAN 2
  D. adds it to the VLAN database
  A. Drops the packet

• Question 527:

  ROUTER# show ip route 192.168.12.0/24 is variably subnetted, 9 subnets, 3 masks C 192.168.12.64 /28 is directly connected, Loopback1 C 192.168.12.32 /28 is directly connected, Ethernet0 C 192.168.12.48 /28 is directly connected, Loopback0 O 192.168.12.236 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 C 192.168.12.232 /30 is directly connected, Serial0 O 192.168.12.245 /30 [110/782] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.240 /30 [110/128] via 192.168.12.233, 00:35:36, Serial0 O 192.168.12.253 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.249 /30 [110/782] via 192.168.12.233, 00:35:37, Serial0 O 192.168.12.240/30 [110/128] via 192.168.12.233, 00:35:36, Serial 0

  To what does the 128 refer to in the router output above?

  A. OSPF cost
  B. OSPF priority
  C. OSPF hop count
  D. OSPF ID number
  E. OSPF administrative distance
  A. OSPF cost

• Question 528:

  Which feature is only supported by named access lists?

  A. TCP flag filtering
  B. destination-address filtering
  C. logging
  D. contiguous ports
  A. TCP flag filtering

• Question 529:

  Refer to the exhibits labeled A through E. All devices are to be connected over Ethernet. Which three device-to-device configurations are likely to require the use of a crossover connection? (Choose three.)

  

  A. exhibit A
  B. exhibit B
  C. exhibit C
  D. exhibit D
  E. exhibit E
  A. exhibit A
  D. exhibit D
  E. exhibit E

• Question 530:

  Which MTU size can cause a baby giant error?

  A. 1500
  B. 9216
  C. 1600
  D. 1518
  C. 1600