1. Home
  2. Fortinet
  3. NSE7_EFW-6.2

Fortinet NSE7_EFW-6.2 Online Practice Questions and Exam Preparation

NSE7_EFW-6.2 Exam Details

  • Exam Code
    :NSE7_EFW-6.2
  • Exam Name
    :Fortinet NSE 7 - Enterprise Firewall 6.2
  • Certification
    :Fortinet Certifications
  • Vendor
    :Fortinet
  • Total Questions
    :102 Q&As
  • Last Updated
    :May 26, 2026

Fortinet NSE7_EFW-6.2 Online Questions & Answers

  • Question 91:

    Examine the following partial output from a sniffer command; then answer the question below.

    What is the meaning of the packets dropped counter at the end of the sniffer?

    A. Number of packets that didn't match the sniffer filter.
    B. Number of total packets dropped by the FortiGate.
    C. Number of packets that matched the sniffer filter and were dropped by the FortiGate.
    D. Number of packets that matched the sniffer filter but could not be captured by the sniffer.

  • Question 92:

    Examine the output of the 'diagnose debug rating' command shown in the exhibit; then answer the question below.

    Which statement are true regarding the output in the exhibit? (Choose two.)

    A. There are three FortiGuard servers that are not responding to the queries sent by the FortiGate.
    B. The TZ value represents the delta between each FortiGuard server's time zone and the FortiGate's time zone.
    C. FortiGate will send the FortiGuard queries to the server with highest weight.
    D. A server's round trip delay (RTT) is not used to calculate its weight.

  • Question 93:

    An administrator has configured two FortiGate devices for an HA cluster. While testing the HA failover, the administrator noticed that some of the switches in the network continue to send traffic to the former primary unit. The administrator decides to enable the setting link-failed-signal to fix the problem. Which statement is correct regarding this command?

    A. Forces the former primary device to shut down all its non-heartbeat interfaces for one second while the failover occurs.
    B. Sends an ARP packet to all connected devices, indicating that the HA virtual MAC address is reachable through a new master after a failover.
    C. Sends a link failed signal to all connected devices.
    D. Disables all the non-heartbeat interfaces in all the HA members for two seconds after a failover.

  • Question 94:

    Which configuration can be used to reduce the number of BGP sessions in an IBGP network?

    A. Neighbor range
    B. Route reflector
    C. Next-hop-self
    D. Neighbor group

  • Question 95:

    What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.)

    A. Reduce the session time to live.
    B. Increase the TCP session timers.
    C. Increase the FortiGuard cache time to live.
    D. Reduce the maximum file size to inspect.

  • Question 96:

    View the exhibit, which contains the output of diagnose sys session list, and then answer the question below.

    If the HA ID for the primary unit is zero (0), which statement is correct regarding the output?

    A. This session is for HA heartbeat traffic.
    B. This session is synced with the slave unit.
    C. The inspection of this session has been offloaded to the slave unit.
    D. This session cannot be synced with the slave unit.

  • Question 97:

    Refer to the exhibit, which contains the output of a BGP debug command.

    Which statement about the exhibit is true?

    A. The local router has received a total of three BGP prefixes from all peers.
    B. The local router has not established a TCP session with 100.64.3.1.
    C. Since the counters were last reset, the 10.200.3.1 peer has never been down.
    D. The local router BGP state is OpenConfirm with the 10.127.0.75 peer.

  • Question 98:

    The CLI command set intelligent-mode controls the IPS engine's adaptive scanning behavior. Which of the following statements describes IPS adaptive scanning?

    A. Determines the optimal number of IPS engines required based on system load.
    B. Downloads signatures on demand from FDS based on scanning requirements.
    C. Determines when it is secure enough to stop scanning session traffic.
    D. Choose a matching algorithm based on available memory and the type of inspection being performed.

  • Question 99:

    The logs in a FSSO collector agent (CA) are showing the following error: failed to connect to registry: PIKA1026 (192.168.12.232)

    What can be the reason for this error?

    A. The CA cannot resolve the name of the workstation.
    B. The FortiGate cannot resolve the name of the workstation.
    C. The remote registry service is not running in the workstation 192.168.12.232.
    D. The CA cannot reach the FortiGate with the IP address 192.168.12.232.

  • Question 100:

    View the exhibit, which contains the output of a web diagnose command, and then answer the question below.

    Which one of the following statements explains why the cache statistics are all zeros?

    A. The administrator has reallocated the cache memory to a separate process.
    B. There are no users making web requests.
    C. The FortiGuard web filter cache is disabled in the FortiGate's configuration.
    D. FortiGate is using a flow-based web filter and the cache applies only to proxy-based inspection.

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Fortinet exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your NSE7_EFW-6.2 exam preparations and Fortinet certification application, do not hesitate to visit our Vcedump.com to find your solutions here.