NetApp NS0-509 Online Practice Questions and Exam Preparation

NetApp NS0-509 Online Questions & Answers

• Question 121:

  You are planning to set up a new SAN with an AFF A300 2-node switchless cluster. Your SAN fabric will consist of Cisco MDS9148s switches. According to NetApp best practices, which two actions would be required to accomplish this task? (Choose two.)

  A. Set the switchport speed setting to 16 Gb.
  B. Use single initiator, multiple target zoning.
  C. Use multiple initiator, single target zoning.
  D. Set the switchport speed to auto negotiate.
  B. Use single initiator, multiple target zoning.
  D. Set the switchport speed to auto negotiate.

• Question 122:

  Click the Exhibit button.

  

  You have a requirement to serve LUNs with under 200 microsecond latency using local server lass memory. You also are required to use a shared SAN. Using MAX Data as shown in the exhibit, which two LUN access protocols are supported with this solution? (Choose two.)

  A. iSCSI
  B. FCoE
  C. FC
  D. NVMe
  A. iSCSI
  C. FC

• Question 123:

  A customer that is using an AFF A220 has a problem with a host for a new FC LUN. Other LUNs on the same SVM are working properly. This LUN is not visible on the host. Which configuration does the customer need to verify in their solution?

  A. LUN mapping with igroup
  B. host HBA speed settings
  C. FC target port setting on NetApp node
  D. FC switch zoning
  C. FC target port setting on NetApp node

• Question 124:

  You are provisioning storage to an ESX host that uses iSCSI.

  According to NetApp best practice, which three actions accomplish this task? (Choose three.)

  A. Enable the iSCSI service.
  B. Bind the iSCSI ports to the software iSCSI adapter.
  C. Install Virtual Storage Console (VSC) for VMware.
  D. Enable BGP on the switch.
  E. Configure MTU 1500 on the switch.
  B. Bind the iSCSI ports to the software iSCSI adapter.
  C. Install Virtual Storage Console (VSC) for VMware.
  E. Configure MTU 1500 on the switch.

• Question 125:

  An administrator wants to design an NVMe solution to connect Linux hosts to an ONTAP cluster. The proposed solution uses two Cisco MDS 9396T switches for each fabric in a top-of-rack design. In this scenario, which statement is true?

  A. Asymmetric Namespace Access requires ONTAP 9.4 and higher.
  B. NVMe solutions require heterogeneous multiple switch fabrics.
  C. N_Port ID virtualization (NPIV) must be enabled on all switches.
  D. A middle-of-rack design is required.
  C. N_Port ID virtualization (NPIV) must be enabled on all switches.

• Question 126:

  A customer has an existing 8-node cluster that consists of six FAS2650 nodes and two FAS2554 nodes. The customer wants to expand the cluster by adding two AFF A220 nodes. Which resource would be used to determine whether this configuration is supported?

  A. Interoperability Matrix Tool (IMT)
  B. Config Advisor
  C. OneCollect
  D. Hardware Universe (HWU)
  B. Config Advisor

• Question 127:

  Click the Exhibit button.

  

  You have a performance critical database application that is running on a FAS9000 controller that uses FC. As shown in the exhibit, volume efficiency is enabled. If you follow the performance recommendation, what are two results to the data in the volume? (Choose two.)

  A. The new written data is compressed.
  B. The new written data is uncompressed.
  C. The existing data is uncompressed.
  D. The existing data is compressed.
  A. The new written data is compressed.
  C. The existing data is uncompressed.

• Question 128:

  An SVM's LUN setup needs to have LIFs that are configured for FC access and iSCSI access. The administrator will also be using NetApp Virtual Storage Console. In this scenario, which three types of LIFs are required? (Choose three.) FC LIFs

  A. management LIFs
  B. iSCSI data LIFs
  C. NAS data LIFs
  D. intercluster LIFs
  A. management LIFs
  B. iSCSI data LIFs
  C. NAS data LIFs

• Question 129:

  Click the Exhibit button.

  

  You have a 2-node cluster in a single-fabric SAN. Host 1 and Host 2 are part of a VMware cluster and access the same LUNs that reside in your NetApp storage. Referring to the exhibit, what would be a way to test whether the multipathing is properly configured in your environment?

  A. Verify whether all destination storage target ports are contained in the same zone as Host 1.
  B. Administratively set ports 0a and 0c on Controller 1 to the offline setting.
  C. Power off the SAN switch.
  D. Disconnect Host 1 port and verify whether Host 2 is still able to run the VMs.
  B. Administratively set ports 0a and 0c on Controller 1 to the offline setting.

• Question 130:

  A user cannot add more than one NVMe data LIF in ONTAP 9.4 on an SVM with a data protocol parameter set to nvme. In this scenario, what is the problem?

  A. The SVM data protocol should be set to FC.
  B. The NVMe namespace is not created.
  C. A demo license is used.
  D. Only one NVMe data LIF can be configured per SVM.
  B. The NVMe namespace is not created.