Juniper JN0-362 Online Practice Questions and Exam Preparation

Juniper JN0-362 Online Questions & Answers

• Question 21:

  According to Juniper Networks, what are two reasons to peer using loopback addresses when configuring BGP? (Choose two.)

  A. When establishing an IBGP connection
  B. When routers are not in the same autonomous system
  C. When routers are not directly connected
  D. When establishing a single-link EBGP connection
  A. When establishing an IBGP connection
  C. When routers are not directly connected

• Question 22:

  Click the Exhibit button.

  

  You configured R1 and R2 to form an OSPF adjacency, but the adjacency will not establish. Referring to the exhibit, which statement correctly identifies the problem?

  A. Hello and dead timers are not matching between R1 and R2
  B. R1 does not have a router ID defined
  C. R1 and R2 have the same router ID
  D. R2 has a wrong area configured
  C. R1 and R2 have the same router ID

• Question 23:

  What is the Junos default router priority advertisement value for IS-IS?

  A. 64
  B. 32
  D. 127
  A. 64

• Question 24:

  Click the Exhibit button.

  

  You have configured IPv6 over IPv4 tunneling, as shown in the exhibit. However, hosts connected to network 2001:0:0:1::0/64 cannot communicate with hosts on network 2001:0:0:2::0/64. The router R2 has a similar configuration as the R1 router.

  How would you solve this problem?

  A. Configure an IGP across the tunnel interfaces
  B. Configure an IPv6 address on the tunnel interfaces
  C. Configure the next hop of the inet6.0 static route to point to the physical interface between the routers
  D. Configure the next hop of the inet6.0 static route to point to the IPv4 address of the remote router
  D. Configure the next hop of the inet6.0 static route to point to the IPv4 address of the remote router

• Question 25:

  In a stateless IPv6 auto-configuration scenario, what is the host's IPv6 address if the interface's MAC address is 12:34:ab:cd:ef:56?

  A. fe80::1234:abff:fecd:ef56/64
  B. fe8::1234:abff:fecd:ef56/64
  C. fec0::1234:abff:fecd:ef56/64
  D. fe80::1234:abcd:ef56/64
  D. fe80::1234:abcd:ef56/64

• Question 26:

  Click the Exhibit button.

  

  Referring to the exhibit, which statement about the IS-IS interface is true?

  A. The ge-0/0/0.0 interface will act as an L1/L2 interface
  B. The ge-0/0/0.0 interface will act as an L2 interface only
  C. The ge-0/0/0.0 interface will act as an L1 interface only
  D. The ge-0/0/0.0 interface will not be assigned to a level
  A. The ge-0/0/0.0 interface will act as an L1/L2 interface

• Question 27:

  Click the Exhibit button.

  

  You must create a static route on Router-A to the 10.10.5.0/24 network using 10.10.3.2 as the next hop. Referring to the exhibit, which configuration accomplishes this task?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  D. Option D

• Question 28:

  Click the Exhibit button.

  

  Both configuration hierarchies shown in the exhibit have been committed to your MX Series device. Which two statements are true in this scenario? (Choose two.)

  A. Traffic destined to 10.3.0.1 will use the R1-to-R6 LSP as a next hop
  B. Traffic destined to 10.3.0.1 will not use the R1-to-R6 LSP as a next hop
  C. The active 10.3.0.0/24 prefix installed in the route table will have a route preference of 5
  D. The active 10.3.0.0/24 prefix installed in the route table will have a route preference of 7
  A. Traffic destined to 10.3.0.1 will use the R1-to-R6 LSP as a next hop
  D. The active 10.3.0.0/24 prefix installed in the route table will have a route preference of 7

• Question 29:

  Which two statements are true about IP and GRE tunnels? (Choose two.)

  A. The protocol field is changed in the inner IP packet header
  B. Tunnel traffic is encrypted
  C. The TTL field is changed in the inner IP packet header
  D. Tunnel endpoints need a valid route to the remote endpoint
  C. The TTL field is changed in the inner IP packet header
  D. Tunnel endpoints need a valid route to the remote endpoint

• Question 30:

  Click the Exhibit button.

  

  Referring to the exhibit, which statement is correct?

  A. Routes from 10.1.1.1 are more preferred than routes from 10.2.2.2
  B. Routes from 10.2.2.2 are less preferred than the default local preference
  C. Routes from 10.3.3.3 are more preferred than the default local preference
  D. Routes from 10.2.2.2 are less preferred than routes from 10.3.3.3
  C. Routes from 10.3.3.3 are more preferred than the default local preference