Juniper JN0-362 Online Practice Questions and Exam Preparation

Juniper JN0-362 Online Questions & Answers

• Question 1:

  Which of following two statements are true for GRE tunneling? (Choose two.)

  A. GRE tunnels are stateful by default
  B. GRE tunnels support multiple logical units per interface
  C. GRE tunnels support only one logical unit per interface
  D. GRE tunnel endpoints must have a valid route to the remote endpoint
  B. GRE tunnels support multiple logical units per interface
  D. GRE tunnel endpoints must have a valid route to the remote endpoint

• Question 2:

  Click the Exhibit button.

  

  Which type of route is shown in the exhibit?

  A. generate
  B. static
  C. kernel
  D. aggregate
  A. generate

• Question 3:

  You want to make use of the nonstop active routing (NSR) feature. Which complementary feature must also be enabled?

  A. IP anycast
  B. graceful restart
  C. Virtual Router Redundancy Protocol
  D. graceful Routing Engine switchover
  D. graceful Routing Engine switchover

• Question 4:

  Which statement about a virtual-router type of routing instance is correct?

  A. It is used to separate large networks into smaller administrative entities
  B. It is the only routing instance type supported on Junos devices
  C. It is used in Layer 3 VPN implementations
  D. It is used to create and maintain separate routing and forwarding tables
  D. It is used to create and maintain separate routing and forwarding tables

• Question 5:

  Click the Exhibit button.

  

  Referring to the exhibit what are two reasons for the configuration stanza? (Choose two.)

  A. to reduce the risk of forwarding traffic through a stateless tunnel
  B. to mark the tunnel down after the hold-time expires
  C. to remove the tunnel interface from inet.0 after the hold-time expires
  D. to mark the tunnel up after the hold-time expires
  A. to reduce the risk of forwarding traffic through a stateless tunnel
  B. to mark the tunnel down after the hold-time expires

• Question 6:

  Click the Exhibit button.

  

  You configured R1 and R2 to form an OSPF adjacency, but the adjacency will not establish. Referring to the exhibit, which statement correctly identifies the problem?

  A. Hello and dead timers are not matching between R1 and R2
  B. R1 does not have a router ID defined
  C. R1 and R2 have the same router ID
  D. R2 has a wrong area configured
  C. R1 and R2 have the same router ID

• Question 7:

  What is the purpose of STP BPDUs?

  A. to exchange MAC addresses
  B. to determine the least cost path
  C. to determine the root-alternate port
  D. to determine the root bridge
  B. to determine the least cost path

• Question 8:

  Which IPv6 extension header notifies intermediary devices that they must inspect the packet's options?

  A. destination options header
  B. routing header
  C. hop-by-hop options header
  D. fragment header
  B. routing header

• Question 9:

  Click the Exhibit button.

  

  You are asked to configure OSPF for the network? Referring to the exhibit, how should Area 1 be configured?

  A. stub area
  B. totally stubby area
  C. not-so-stubby area
  D. backbone area
  A. stub area

• Question 10:

  Which two characteristics describe IS-IS? (Choose two.)

  A. A collection of Level 1 routers serves as the IS-IS backbone
  B. Level 2 routers connect areas in an IS-IS autonomous system
  C. A collection of Level 2 routers serve as the IS-IS backbone
  D. A Level 1 IS routes between areas and toward other autonomous systems
  B. Level 2 routers connect areas in an IS-IS autonomous system
  C. A collection of Level 2 routers serve as the IS-IS backbone