Juniper Juniper Other Certifications JN0-362 Questions & Answers

• Question 11:

  Which two characteristics describe IS-IS? (Choose two.)

  A. A collection of Level 1 routers serves as the IS-IS backbone

  B. Level 2 routers connect areas in an IS-IS autonomous system

  C. A collection of Level 2 routers serve as the IS-IS backbone

  D. A Level 1 IS routes between areas and toward other autonomous systems

  Correct Answer: BC

  Reference: https://www.juniper.net/documentation/en_US/junos/topics/concept/isis-levelsunderstanding.html

• Question 12:

  When working with an MPLS LSP, what will the install 172.16.6.0/24 active command accomplish?

  A. The command will swap the prefix from inet.0 to inet.3

  B. The command will swap the prefix from inet.3 to inet.0

  C. The command will install the prefix in inet.0 rather than inet.3

  D. The command will install the prefix in inet.3 rather than inet.0

  Correct Answer: D

  Reference: https://www.juniper.net/documentation/en_US/junos/topics/topic-map/lsp-routes.html#id-21214

• Question 13:

  Click the Exhibit button.

  

  In the network shown in the exhibit, all switches are configured with the default STP root bridge priority, and Switch A has been selected as root. You recently added the older Switch D into the network as an access switch, and notice it has taken over as root.

  Which configuration would solve this problem?

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  Correct Answer: C

  Reference: https://www.juniper.net/documentation/en_US/junos/topics/reference/configuration-statement/ no-root-port-edit-protocols-stp.html

• Question 14:

  Click the Exhibit button.

  

  You have applied the policy shown in the exhibit to the forwarding table on an MX Series device. How is traffic load-balanced?

  A. per frame

  B. per packet

  C. per segment

  D. per flow

  Correct Answer: B

• Question 15:

  Click the Exhibit button.

  

  Customer-1 wants the Service Provider to allow STP to operate normally on all ports but only allow the MX Series devices to manage the Layer 2 topology.

  Referring to the exhibit, which feature needs to be implemented on all devices to accomplish this task?

  A. root protection

  B. MAC movement protection

  C. BPDU protection

  D. loop protection

  Correct Answer: D

• Question 16:

  Click the Exhibit button.

  

  Referring to the exhibit, which statement is correct?

  A. Routes from 10.1.1.1 are less preferred than the default local preference

  B. Routes from 10.2.2.2 are less preferred than routes from 10.1.1.1

  C. Routes from 10.3.3.3 are less preferred than the default local preference

  D. Routes from 10.1.1.1 are less preferred than routes from 10.2.2.2

  Correct Answer: B

• Question 17:

  Click the Exhibit button.

  

  Referring to the exhibit, how many milliseconds must pass before the interface ge-0/0/1.0 is considered down?

  A. 1200 ms

  B. 900 ms

  C. 1600 ms

  D. 2400 ms

  Correct Answer: A

• Question 18:

  Which two statements are true about IBGP on MX Series devices? (Choose two.)

  A. Neighbors can be located anywhere within the AS

  B. Interface Lo0 must be used for peering

  C. It does not support multihop

  D. It is loop free by default

  Correct Answer: AD

  Reference: https://www.juniper.net/documentation/en_US/junos/topics/topic-map/bgp-ibgp-peering.html

• Question 19:

  According to Juniper Networks, what are two reasons to peer using loopback addresses when configuring BGP? (Choose two.)

  A. When establishing an IBGP connection

  B. When routers are not in the same autonomous system

  C. When routers are not directly connected

  D. When establishing a single-link EBGP connection

  Correct Answer: AC

• Question 20:

  Click the Exhibit button.

  

  Referring to the exhibit, if there is a connection failure between router1 and router2, how much time will pass before the devices declare the BFD session dead?

  A. 1200 ms

  B. 300 ms

  C. 600 ms

  D. 900 ms

  Correct Answer: D