HP HPE6-A29 Online Practice Questions and Exam Preparation

HP HPE6-A29 Online Questions & Answers

• Question 71:

  When are the system-defined default roles added to the configuration on the controller?

  A. when the controller is first booted
  B. when an RF Protect license is added to the controller
  C. when created manually
  D. when a PEF-NG license is added to the controller
  D. when a PEF-NG license is added to the controller

• Question 72:

  With CPSec disabled, which encryption protocol does a tunnel mode campus AP's use on client traffic ?

  A. TKIP and AES
  B. It is provisioned by the Administrator
  C. WEP and AES
  D. WEP, TKIP, and AES
  E. No encryption is used
  E. No encryption is used

• Question 73:

  Examine the configuration file segment from an Aruba Mobility Controller. ip access-list session anewone user network 10.1.1.0 255.255.255.0 any permit user host 10.1.1.1 any deny user any any permit What can administrator conclude from this?

  A. This is an extended Access Control List (ACL)
  B. Any traffic going to destination 172.16.197.713 will be permitted
  C. Any traffic going to destination 10.1.1.1 will be denied.
  D. This is a session firewall policy.
  B. Any traffic going to destination 172.16.197.713 will be permitted

• Question 74:

  Which profiles are required in an AP Group to enable an SSID with VLAN 1, WPA2 and LMSIP? (Choose three)

  A. Virtual-ap ap mesh-radio-profile ap system profile
  B. Wlan ssid-profile ap-system-profile virtual-ap profile
  C. 802.1X authentication profile wlan ssid-profile virtual-ap profile
  D. Virtual-ap profile ap-system profile aaa profile
  B. Wlan ssid-profile ap-system-profile virtual-ap profile

• Question 75:

  

  A user logged in with the Captive Portal settings shown in the above screen capture.

  What does the user need to do to logout?

  A. wait 30 minutes then logout
  B. wait 60 minutes then logout
  C. click Logout on the browser screen
  D. he cannot logout
  E. wait 10 seconds for redirect
  C. click Logout on the browser screen

• Question 76:

  (group8) #show ap active Active AP Table

  Name Group IP Address 11g Clients 11g Ch/EIRP/MaxEIRP 11a Clients 11a Ch/EIRP/MaxEIRP

  AP1 building1 10.1.80.150 0 AM 0 AM

  AP2 building1 10.1.80.151 0 AM 0 AM

  A user called technical support because they cannot see any of their APs in building one. You perform the "show" command as illustrated above.

  What can you conclude about these two APs from this output?

  A. the GRE for the APs terminate on two different controllers: 10.1.80.150 and 10.1.80.151
  B. the system will not function because there is no building1 group defined
  C. the building1 APs will not accept any user connections
  D. the user needs to configure his client to use the b/g band
  E. the user needs to configure his client to use the a band
  C. the building1 APs will not accept any user connections

• Question 77:

  An AP was configured to use dynamic controller discovery and assigned to an AP group, then powered off for over a week. When the AP is redeployed, what previous configuration will it retain?

  A. Its AP name and AP Group
  B. Its Serial Number
  C. The controller's IP address
  D. After a few days all configurations are lost
  E. The controller IP address and the AP Group
  A. Its AP name and AP Group

• Question 78:

  An AP125 has been provisioned as a Campus AP in the default AP group. It has booted but the radio lights are orange. What might be a cause of this? Select all that apply.

  A. The AP has booted successfully and is broadcasting wireless networks
  B. The VAP does not have a VLAN assigned to it
  C. The antenna gain parameters of the AP must be provisioned
  D. The default AP Group does not have any VAPs assigned to it
  B. The VAP does not have a VLAN assigned to it
  D. The default AP Group does not have any VAPs assigned to it

• Question 79:

  What is the purpose of Mesh Clusters?

  A. To separate Mesh points from Mesh Portals.
  B. To ensure that mesh APs with the same VAPs are not in the same cluster.
  C. To define a group of mesh APs that create mesh links with each other.
  D. To cluster mesh APs of the same model together.
  E. To enable mesh APs to join the nearest mesh portal cluster.
  C. To define a group of mesh APs that create mesh links with each other.

• Question 80:

  Which of the following statements allows a user to initiate an HTTP session to other devices?

  A. any alias internal-nets svc-dns permit
  B. user any svc-http permit
  C. user user svc-http permit
  D. any any svc-http permit
  B. user any svc-http permit
  D. any any svc-http permit