HP HP2-Z30 Online Practice Questions and Exam Preparation

HP HP2-Z30 Online Questions & Answers

• Question 31:

  A network administrator receives a new HP Provision switch and notices that the software version running on the switch is older than what is currently used in the network. The network administrator copies an updated version of the operating

  system from the new switch's USB port to the secondary flash location. The network administrator then executes the following command:

  Provision# boot system flash secondary:

  The switch reboots using the new operating system. However, when the network administrator turns off the switch and turns it back on, the switch boots from the old operating system.

  Which solution should the network administrator use to fix the problem?

  A. Execute the startup-boot secondary command.
  B. Boot into the switch's Monitor ROM Console and perform the upgrade a second time.
  C. Execute the boot set-default flash secondary command.
  D. Execute the boot-loader file command.
  E. Execute the startup-default secondary command.
  C. Execute the boot set-default flash secondary command.

• Question 32:

  Which statement is correct about IRF?

  A. Identical models of switches must be used in the same IRF domain.
  B. Logical IRF port one on a switch must be connected to IRF port two on a second switch.
  C. MSTP is used to remove loops within an IRF domain.
  D. LACP is used to build IRF port connections between switches.
  B. Logical IRF port one on a switch must be connected to IRF port two on a second switch.

• Question 33:

  Which HP Comware command can a network administrator execute to view the IP routing table?

  A. display ip routing-table
  B. show ip route
  C. show ip routing-table
  D. display ip route
  A. display ip routing-table

• Question 34:

  Refer to the exhibit.

  

  The link aggregation is failing between the HP Provision and HP Comware switches. Which solution solves this problem?

  A. The interfaces used for trunking on the Provision switch must be continuous.
  B. The Provision switch must be reconfigured for dynamic LACP
  C. The Comware switch must be reconfigured for static LACP O
  D. The Comware switch must be reconfigured for dynamic LACP.
  D. The Comware switch must be reconfigured for dynamic LACP.

• Question 35:

  Refer to the network exhibit.

  

  A network administrator has created a Layer 2 network based on the design shown in the exhibit. Switch-A and Switch-B are distribution layer switches. Switch-C is an access layer switch. All switches are HP Comware switches. What is the best spanning tree solution for load sharing on uplinks in this environment?

  A. STP
  B. MSTP
  C. RSTP
  D. distributed trunking
  B. MSTP

• Question 36:

  

  Switch 1 and Switch 2 are HP ProVision switches operating as Layer 2 switches. VLAN 33 has been defined as the management VLAN on both switches. Based on this topology, which user devices can access Switch 1 by using SSH?

  A. only User-1, User-2, and the Server
  B. only User-1
  C. all users and servers in the topology
  D. only User-1 and User-2
  B. only User-1

• Question 37:

  A network administrator is using Intelligent Management Center (IMC). Which protocol must the networkadministrator configure to correctly identify HP devices when performing auto discovery?

  A. telnet
  B. LLDP
  C. SSH
  D. SNMP
  D. SNMP

• Question 38:

  A network administrator executes this command on an HP switch: Provision (config)# vlan 11 untag Al The network administrator immediately realizes that the port that was specified in the command was the wrong port. Port A1 should remain in its original VLAN, VLAN 1. Which command should the network administrator execute to undo the

  misconfiguration?

  A. vlan 11 tagged Al
  B. vlan 1 tagged Al
  C. vlan 1 untag Al
  D. no vlan 11 untag Al
  A. vlan 11 tagged Al

• Question 39:

  What is the console port designation for an HP Comware switch?

  A. interface console
  B. con 0
  C. aux 0
  D. console
  C. aux 0

• Question 40:

  What is the initial OSPF state of a router when an interface becomes active for a segment?

  A. init
  B. loading
  C. two-way
  D. down
  D. down