HP HP2-Z30 Online Practice Questions and Exam Preparation

HP HP2-Z30 Online Questions & Answers

• Question 1:

  Which HP redundancy feature is supported by both HP Provision and HP Comware switches?

  A. meshed stacking
  B. distributed trunking
  C. static link aggregation
  D. dynamic LACP
  C. static link aggregation

• Question 2:

  A network administrator is building two IRF domains:

  1.

  One domain for the two distribution layer switches

  2.

  One domain for the access layer switches

  Each access layer switch should have a connection to each distribution layer switch. In this design, how many access switches can the administrator have in the access layer IRF domain before spanning tree is required to remove loops between the two IRF domains?

  A. 2
  B. 4
  C. 6
  D. 8
  E. 12
  A. 2

• Question 3:

  A network administrator has an HP Comware switch that is configured with OSPF. The network administrator views the routing table and sees that a default route was learned from an OSPF neighbor (10.1.1.1). However, the network

  administrator wants to override this action and use a different neighbor (10.1.1 2) for the default route.

  The network administrator configures this command:

  [Comware] ip route-static 0.0.0.0 0 10.1.1.2

  After configuring the command, the network administrator examines the routing table and notices that the original neighbor's default route is still in the routing table, but the static route is missing.

  What is the cause of this problem?

  A. OSPF routes have a lower precedence value
  B. The ip default-gateway command must be used when creating a default route
  C. Only one routing protocol can be operational on a Comware device
  D. The static route has a syntax mistake
  A. OSPF routes have a lower precedence value

• Question 4:

  Which protocol only requires MAC addressing?

  A. LLDP
  B. DHCP
  C. NTP
  D. Syslog
  A. LLDP

• Question 5:

  Which IMC agent starts and stops the IMC server and allows a network administrator to view the status of the IMC processes?

  A. Policy Administration Agent (PAA)
  B. Deployment Monitoring Agent (DMA)
  C. Administration Deployment Agent (ADA)
  D. IMC Processing Agent (IPA)
  B. Deployment Monitoring Agent (DMA)

• Question 6:

  What is the default username and password an administrator would use to log into a new HP MSM access point?

  A. username of "hp" and password of "hp"
  B. username of "msm" and password of "wireless"
  C. username of "admin" and password of "hp"
  D. username of "admin" and password of "admin"
  D. username of "admin" and password of "admin"

• Question 7:

  Refer to the topology output.

  

  Based on this topology, which statements are true? (Select two)

  A. The topology is functioning normally
  B. This is a daisy chain topology
  C. This is a ring topology
  D. A break exists in the topology
  E. There is a split stack
  C. This is a ring topology
  D. A break exists in the topology

• Question 8:

  Which statement is true concerning PoE support on HP ProVision and HP Comware switches?

  A. Both the IEEE 802.3af and 802.3az power standards are supported.
  B. PoE is enabled by default on PoE-capable ports.
  C. Lowered-number ports, by default, have higher priority for Power requests.
  D. SNMP is used to determine power requirements of a connected devices.
  B. PoE is enabled by default on PoE-capable ports.

• Question 9:

  A network administrator has installed IMC and the appropriate licenses. The network administrator is attempting to import the HP Comware and HP ProVision switches into IMC but is experiencing problems importing the Comware switches.

  The network administrator verifies the SNMPv2c configuration on both sets of switches and the SNMP configuration in IMC. The SNMP parameters are correct. What is the cause of the import problem?

  A. Comware switches implement SNMPv3 by default.
  B. Comware switches require SSH to be configured for remote CLI access.
  C. Comware switches are not fully supported by IMC.
  D. Comware switches do not have telnet fully configured.
  D. Comware switches do not have telnet fully configured.

• Question 10:

  A customer must connect networks in two buildings. The buildings are 15 meters apart. The customer does not want the additional cost of installing fiber between the two buildings and thus is exploring wireless options. If the customer selects an 802.11n wireless solution, which wireless mode should they use?

  A. inline
  B. infrastructure
  C. in-cell relay
  D. multipoint
  C. in-cell relay