HP HP2-K34 Online Practice Questions and Exam Preparation

HP HP2-K34 Online Questions & Answers

• Question 31:

  You are installing an HP 3PAR StoreServ array. The operating systems are Windows 2012, VMware ESX 5.x, and Linux In addition to the HP 3PAR Operating System Software Suite, the customer has purchased the HP 3PAR Replication Software Suite and HP 3PAR Data Optimization Software Suite. The customer intends to use Adaptive Optimization for the Windows 2012 systems and Remote Copy for the Windows 2012 and VMware ESX 5.x systems. The Linux systems have high write ratios, often exceeding 63%. Virtual Copy snapshots will be heavily used, and there is a requirement to monitor total snapshot capacity.

  You are asked to create the following CPGs: Type RAID SSD 1 FC 5 NL 6 After validating the design with the HP 3PAR StoreServ Storage best practices guide, which recommendation should you make?

  A. Limit the CPGs to a maximum of 64 TB
  B. Set the CPGs for magazine availability
  C. Use the same CPG for Virtual Copies and the base Virtual Volumes.
  D. Create additional CPGs
  D. Create additional CPGs

• Question 32:

  As a consultant, you are configuring Peer Motion during an initial setup of the HP 3PAR StoreServ systems. What must you consider to ensure the correct configuration of a Peer Motion environment?

  A. Executing the Peer Motion Manager script requires Browse user-rights for the accounts used to log in to the source array and Super user-rights for the destination array.
  B. Two FC switches are required; only fabric connections on initiator ports are supported, and the host and source system must use the same IP protocol version.
  C. The Peer Motion Manager script executes in a command window of Microsoft Windows running on a Peer Motion Manager Server.
  D. The WWN of the VLUNs imported to the new array will become the S/N of the legacy array.
  C. The Peer Motion Manager script executes in a command window of Microsoft Windows running on a Peer Motion Manager Server.

• Question 33:

  What should you discuss during the customer briefing when you perform installs during the winter months?

  A. The temperature of the operating environment may be below the minimum safe operating temperature for the storage server.
  B. Input AC voltages may be higher than in summer when utilities drop voltages during peak periods
  C. The storage server should be brought into the operating environment at least 24 hours prior to installation.
  D. Lower humidity leads to an increased need for the anti-static kit.
  A. The temperature of the operating environment may be below the minimum safe operating temperature for the storage server.
  C. The storage server should be brought into the operating environment at least 24 hours prior to installation.

• Question 34:

  Match each description to the correct HP 3PAR StoreServ thin technology.

  Hot Area:

  

  

• Question 35:

  You are running the SmartStart Installation procedure to install an HP StoreServ 7400 Storage System. Which users, created during the installation process, will have access to this storage system? (Select two.)

  A. 3paradm
  B. 3parcust
  C. 3parAO
  D. 3parSP
  E. 3PARrm
  A. 3paradm
  B. 3parcust

• Question 36:

  A customer has an HP 3PAR 10400, which consists of a controller rack and one disk rack The customer orders an additional disk rack to upgrade the system. What needs to be considered when installing the additional disk rack into the datacenter?

  A. The additional disk rack cannot be more than 100 meters from the controller rack
  B. Installation of the additional disk rack requires a service outage to the array
  C. The additional disk rack requires support of four controllers at a minimum
  D. The additional disk rack must be installed on the right hand side of the controller rack.
  B. Installation of the additional disk rack requires a service outage to the array

• Question 37:

  What is the loading order of an HP 3PAR StoreServ 10800 with four nodes?

  A. 6, 5, 2, 1
  B. 7, 6, 5, 4
  C. 0, 1, 2, 3
  D. 0, 1, 4, 5
  C. 0, 1, 2, 3

• Question 38:

  Which functionality is enabled when the Secure Network Mode is used?

  A. control of outbound communication access via WBEM
  B. control of inbound communication access via SMI-S
  C. control of inbound/outbound communication access via HTTPS
  D. control of inbound/outbound communication access via SSH session
  B. control of inbound communication access via SMI-S

• Question 39:

  You have just upgraded an HP 3PAR 10400 to the latest supported firmware and patch level. The customer environment consists of a mixture of Red Hat Linux and Windows Server 2012. After the HP 3PAR array firmware upgrade completes, the customer reports that the Red Hat Linux servers can see their LUNs, but the Windows servers cannot. An investigation determines that the Windows servers have marked the HP 3PAR LUNs as Offline.

  Which step will solve this problem?

  A. Use the Windows Logical Disk Manager to set the LUNs as Online
  B. Change all Windows Virtual Volumes to Online in the IMC.
  C. Set the Microsoft native MPIO driver load-balancing policy to Active/Passive
  D. Change the Scsi.ConflictRetries setting from its default value of 80 to a value of 200
  D. Change the Scsi.ConflictRetries setting from its default value of 80 to a value of 200

• Question 40:

  Which type of cable is used to mesh the controller nodes in an HP 3PAR StoreServ 7400?

  A. Fibre Channel
  B. proprietary
  C. four-lane SAS
  D. 10 Gb Ethernet DAC
  D. 10 Gb Ethernet DAC