Skip to main content

DES-4421 Real Exam Questions

Specialist - Implementation Engineer, PowerEdge MX Modular

54 questions available · Page 1 of 6

Updated Exam DumpsVerified AnswersPass Guarantee

Get Complete Exam Dumps
Question 1 Single choice

When running an Open Networking operating system, which IOM functions are provided through OME-M?

  1. A

    Global and privileged configuration modes

  2. B

    Power control and global configuration mode

  3. C

    Hardware health and power control

  4. D

    Hardware health and global configuration mode

Show answer and explanation

Correct answer: D

Question 2 Single choice

Where is a valid storage location for extracting the full MX7000 chassis logs package?

  1. A

    VMFS

  2. B

    FTP

  3. C

    CIFS

  4. D

    CSV

Show answer and explanation

Correct answer: C

Explanation

References:
https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/omem1.00.01_ug/sas-iom-overview?guid=guid-35fc46f8-41b1-4b9f-9aa9-037e400ec3f6&lang=en-us

Question 3 Single choice

Which MX7000 feature allows an administrator to virtualize network WWN and MAC addresses?

  1. A

    FlexAddress

  2. B

    MX Scalable Architecture

  3. C

    Identity Pool

  4. D

    Virtual Top of Rack

Show answer and explanation

Correct answer: C

Explanation

References:
https://i.dell.com/sites/csdocuments/Product_Docs/en/
dell_emc_poweredge_mx7000_technical_guide.pdf (p.30)

Question 4 Single choice

An administrator is asked to install and power-on a new MX740c sled in an MX7000 chassis. The administrator inserts the sled and presses the power button. They notice that the power button LED is blinking green. After a short time power button turns to solid green and the server finally turns on.

What operation was in progress when the power button was blinking green?

  1. A

    iDRAC was booting

  2. B

    Lifecycle Controller update was in progress

  3. C

    Lifecycle Controller was taking firmware inventory

  4. D

    iDRAC was updating firmware

Show answer and explanation

Correct answer: A

Question 5 Single choice

What is a characteristic of MX7000 networking in Full Switch Mode?

  1. A

    Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.

  2. B

    Networking is enabled by default and all switch-specific OS10EE capabilities are available.

  3. C

    Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.

  4. D

    Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.

Show answer and explanation

Correct answer: B

Explanation

References:
https://infohub.delltechnologies.com/l/test2-poweredge-mx-networking-architecture-guide-1/
operating-modes-description-7

Question 6 Single choice

An administrator has installed the iDRAC Service Module in the OS on a compute sled, they are unable to use its features in the iDRAC web GUI.

What is the likely cause of this issue?

  1. A

    OS to iDRAC pass-through feature is not enabled in the iDRAC

  2. B

    iDRAC Express license is installed

  3. C

    OS and iDRAC are configured on different networks

  4. D

    Installed OS is not supported

Show answer and explanation

Correct answer: A

Explanation

References:
https://cdn.cnetcontent.com/syndication/mediaserver/inlinecontent/all/0ec/190/0ec19016bfa8284323b12b2aa8d7a07c/original.pdf

Question 7 Single choice

An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up.

Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?

  1. A

    firmwaredownload tftp://server-ip/imagename

  2. B

    install tftp://server-ip/imagename

  3. C

    fwupdate tftp://server-ip/imagename

  4. D

    upgrade tftp://server-ip/imagename

Show answer and explanation

Correct answer: B

Explanation

References:
https://topics-cdn.dell.com/pdf/smartfabric-os10-5-0_en-us.pdf

Question 8 Single choice

What type of connection is used by QuickSync 2?

  1. A

    Bluetooth

  2. B

    NFC

  3. C

    QuickAssist

  4. D

    LTE

Show answer and explanation

Correct answer: A

Explanation

References:
https://www.dell.com/support/manuals/us/en/04/openmanage-mobile-v2.0/omm20iosug/quick-sync-2?guid=guid-49ec3277-3696-4a65-a5cb-123f09f632fe&lang=en-us

Question 9 Drag & drop

DRAG DROP

Match each deployment logical block with its attributes.

Question diagram
Show answer and explanation
Correct answer diagram
Question 10 Drag & drop

DRAG DROP

An administrator is using the OME-M GUI to change the hostname on an unconfigured I/O module inserted in slot A1. They log on to the MX7000 chassis home page.

What is the correct order of steps the administrator should take to set the management IP address?

Question diagram
Show answer and explanation
Correct answer diagram