EMC D-PSC-MN-01 Online Practice Questions and Exam Preparation

EMC D-PSC-MN-01 Online Questions & Answers

• Question 51:

  Which Dell EMC PowerScale Gen 6 components are considered CRUs?

  A. SSD, power supply, fan, and bezel
  B. Back-end switch, power supply, disk drive, and bezel
  C. SSD, power supply, disk drive, and bezel
  D. SSD, memory card, disk drive, and bezel
  C. SSD, power supply, disk drive, and bezel

• Question 52:

  Which items are FRUs on a Dell EMC PowerScale Gen 6.5 node?

  A. SSD, power supply, and front-end NIC
  B. DIMM, system battery, and front-end NIC
  C. DIMM, back-end NIC, and SSD
  D. DIMM, back-end NIC, and power supply
  A. SSD, power supply, and front-end NIC

• Question 53:

  What is the purpose of SolVe Desktop?

  A. Gather logs from the cluster for analysis
  B. Perform pre-upgrade checks on the cluster
  C. Provide centralized access to step-by-step procedures
  D. Provide access to the latest OneFS codes and firmware upgrades
  C. Provide centralized access to step-by-step procedures

• Question 54:

  Which three F200 components can a customer replace?

  A. System Battery
  B. Network Interface Card
  C. CPU module
  D. DIMM
  E. NVDIMM Battery
  A. System Battery
  B. Network Interface Card
  D. DIMM

• Question 55:

  An engineer replaced a failed node in a PowerScale H500 due to hardware issues. They must verity that the replacement node is functioning correctly. What is a crucial step when replacing the failed node in the cluster?

  A. Run a diagnostic test on the replacement node.
  B. Confirm that the replacement node inherits the old serial number from the cluster.
  C. Verify the size of the storage capacity of the replacement node.
  D. Power on the replacement node and ensure it connects to the network without any problems.
  A. Run a diagnostic test on the replacement node.

• Question 56:

  What detail must be verified during installation planning?

  A. IP addresses
  B. SyncIQ license
  C. Switch OS version
  D. Node serial numbers
  A. IP addresses

• Question 57:

  A cluster consists of H400 nodes. A200 nodes, and tour Gen6 bays available tor expansion. An engineer plans to open bays. What is the result?

  A. A300 nodes can be added and become members of the A200 node pool through the compatibility mode.
  B. A300 nodes cannot be installed in this cluster.
  C. A300 nodes can be added, and a new A300 node pool is created.
  D. A300 nodes can be added and become members of the H400 node pool through the compatibility mode.
  A. A300 nodes can be added and become members of the A200 node pool through the compatibility mode.

• Question 58:

  An SSD has failed in Node 1 in a Dell EMC PowerScale F200 cluster. After replacing the drive, which command should be run to ensure the node has finished updating?

  A. Isi devices -d
  B. Isi status -h
  C. Isi devices device list -node-Inn 1
  D. Isi status -q
  C. Isi devices device list -node-Inn 1

• Question 59:

  What type of drive should a customer use to ensure that their data is encrypted?

  A. NVMe
  B. SSD
  C. SED
  D. Hard drive
  C. SED

• Question 60:

  A platform engineer has created a cluster of 8 F200 nodes. A requirement is for each power supply on each node to supply power to the respective node equally. What must the platform engineer do to meet the requirement?

  A. Run the isi config and change the settings in the config subsystem
  B. Cable each node power connection to a different PDU in the rack
  C. Use the iDRAC settings on each node to disable the hot spare feature
  D. Run the isi set -n command to change the power supply behavior
  C. Use the iDRAC settings on each node to disable the hot spare feature