CWNP CWDP-304 Online Practice Questions and Exam Preparation

CWNP CWDP-304 Online Questions & Answers

• Question 1:

  An organization is implementing a new WLAN. They are upgrading a very old 802.11g network that only a few devices used Now. they expect more than 250 devices to use the new WLAN that will operate 802.11ax Aps. What wired-side consideration should you address in your design recommendations?

  A. DHCP pools
  B. Spanning-tree loops
  C. Modem pools
  D. Client ARP tables
  A. DHCP pools

• Question 2:

  While configuring your site survey software for an upcoming manual survey project, you notice the configuration option for "Network Card Simulation". What is the purpose of such a feature and when would you use it?

  A. This setting allows the site survey software to convert the APs measured downlink RF data into a simulated data set as if the same data were transmitted by a specific client station. It is useful for determining uplink client performance when clients are located far from APs as well as projecting cell size for ad hoc networks.
  B. Since WLAN adapters are not typically calibrated by manufacturers, this setting is a form of software calibration in which you can calibrate an (uncalibrated) adapter to match one of the calibrated adapters shown in the list. This process improves the reliability of RF data collection and reporting when uncalibrated adapters are used.
  C. This is the configuration area in which you specify the adapter type that will be used for the site survey so that the survey software can interpret that adapters reported metrics (based on proprietary formulas) into an RF measurement that is standardized by the survey software and known to its users. This is done
  A. This setting allows the site survey software to convert the APs measured downlink RF data into a simulated data set as if the same data were transmitted by a specific client station. It is useful for determining uplink client performance when clients are located far from APs as well as projecting cell size for ad hoc networks.

• Question 3:

  Even when a full pre-design site survey is not performed, what is always recommended to be performed within the deployment areas?

  A. A spectrum analysis walkthrough
  B. An AP-on-a-stick survey of 37% of the facility as this amount provides all of the statistical information required for good design
  C. A scan m the 5 GHz band looking for common loT interferes
  D. A scan in the Sub-i GHz bands to determine If sideband interference will impact 2 4 GHz operations
  A. A spectrum analysis walkthrough

• Question 4:

  You are configuring an 802.11ac AP using manual channel planning. The design specification calls for the current AP to be placed on channel 56 in 5 GHz and to disable the 2.4 GHz radio.

  For what could the 2.4 GHz radio be used if not standard AP operations?

  Response:

  A. PCI DSS encoding
  B. Security monitoring
  C. Bluetooth access
  D. Controller-based channel assignment
  C. Bluetooth access

• Question 5:

  Which of the following items could be considered constraints when performing a network design?(Choose all that apply.)

  A. Timeline
  B. Personnel
  C. Politics
  D. Budget
  A. Timeline
  B. Personnel
  C. Politics
  D. Budget

• Question 6:

  You have designed a WLAN with a plan for 87 APs m a large office building. The customer has informed you that the budget is not as large as they hoped and they can only purchase 53 APs What action should be taken?

  A. Simply increase the output power of the APs by 30 percent to accommodate tor the smaller number of purchased APs
  B. Perform a complete redesign of the wireless network and inform the customer if some original requirements cannot be accomplished
  C. Remove as many walls as possible within the facility so that the signals can travel a g
  D. Use only 2.4 GHz radios because the signals can be received at a greater distance
  B. Perform a complete redesign of the wireless network and inform the customer if some original requirements cannot be accomplished

• Question 7:

  What term refers to the security practice of obfuscating actual data from unintended receivers as the data crosses the transmission medium? Response:

  A. Confidentiality
  B. Authentication
  C. Integrity
  D. Accounting
  E. Nonrepudiation
  A. Confidentiality

• Question 8:

  If you choose to recommend dynamic channel assignment for the APs in your WLAN design what action should you also recommend'?

  A. Ensure that the output power of all APs is set to the maximum allowed in the regulatory domain
  B. Ensure that the output power of an APs is set to the minimum available in the system interface
  C. Replace all antennas with panel antennas instead of omnidirectional antennas
  D. Configure the settings used by the dynamic channel assignment algorithm optimally for your design
  D. Configure the settings used by the dynamic channel assignment algorithm optimally for your design

• Question 9:

  What is the purpose of defining wall materials in WLAN design software?

  A. To ensure the attenuation and reflection of the materials die considered during propagation modeling
  B. So that the floor plan looks as much like the target deployment space as possible
  C. It adds color to the floor plan which makes it easier to identify requirement areas
  D. Manager require it, so WLAN designers should do it.
  A. To ensure the attenuation and reflection of the materials die considered during propagation modeling

• Question 10:

  You are creating an outdoor bridge link that spans more than 1000 yards. Which one of the following antenna types is more likely to be included in the design?

  A. Yagi
  B. Omni
  C. Patch
  D. Panel
  A. Yagi