Cisco 600-601 Online Practice Questions and Exam Preparation

Cisco 600-601 Online Questions & Answers

• Question 41:

  What two things does a router do when it forwards a packet? (Choose two.)

  A. switches the packet to the appropriate outgoing interfaces
  B. computes the destination host address
  C. determines the next hop on the path
  D. updates the destination IP address
  E. forwards ARP requests
  A. switches the packet to the appropriate outgoing interfaces
  C. determines the next hop on the path

• Question 42:

  You are troubleshooting a connectivity problem and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. Which command would you issue to see where the packets stop?

  A. router#ping
  B. router#tracert
  C. router#show ip route
  D. router#show cdp neighbors
  E. router#traceroute
  E. router#traceroute

• Question 43:

  What is a characteristic of cables that are used in articulating equipment arms?

  A. fiber-optic zip-cord construction
  B. shielded copper twisted pair
  C. high flex rated cable
  D. type PLTC cable
  C. high flex rated cable

• Question 44:

  Exhibit:

  

  Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3?

  A. the address of the switch interface that is connected to router interface Fa0/0
  B. the address of the switch interface that is connected to router interface Fa0/1
  C. the address of the host that is connected to Network A
  D. the address of the host that is connected to Network B
  E. the address of the router interface Fa0/0
  F. the address of the router interface Fa0/1
  E. the address of the router interface Fa0/0

• Question 45:

  Exhibit: Refer to the exhibit. A technician enters the exhibited commands to configure a new router on the plant floor, but receives an error message when attempting to save the configuration. What can the technician do to correct the problem?

  

  A. Enter the correct command.
  B. Enter the command at the correct prompt.
  C. Upgrade the amount of flash memory in the router.
  D. Erase NVRAM to make room for the configuration file.
  E. Add NVRAM because there is not enough room for the configuration file.
  A. Enter the correct command.

• Question 46:

  Select and Place:

  

  

• Question 47:

  What are two benefits that are provided by proper grounding and bonding systems? (Choose two.)

  A. higher speed communications
  B. safe discharge of electrostatic energy
  C. lower equipment power consumption
  D. equipotential termination points for equipment and cable shields
  E. lowest carbon footprint
  B. safe discharge of electrostatic energy
  D. equipotential termination points for equipment and cable shields

• Question 48:

  With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid amber?

  A. The port is sending or receiving data.
  B. A link is present.
  C. No link is present.
  D. There is a link fault.
  E. The port is not forwarding.
  E. The port is not forwarding.

• Question 49:

  According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control?

  A. Level 0
  B. Level 1
  C. Level 2
  D. Level 3
  E. Level 4
  D. Level 3

• Question 50:

  Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration?

  A. Telnet encrypts only the login information, not the entire transmission.
  B. SSH requires fewer network resources and no additional configuration.
  C. Telnet is more difficult to use and configure than SSH.
  D. SSH encrypts the login and session information.
  D. SSH encrypts the login and session information.