Cisco 352-001 Online Practice Questions and Exam Preparation

Cisco 352-001 Online Questions & Answers

• Question 301:

  You are planning a migration to a dual-stack IPv4/1Pv6 campus environment while providing a flexible and scalable design with fault isolation. The design should allow IPv6 devices to tunnel over portions of the campus that are not yet natively IPv6-enabled, including wireless and voice endpoints. Your plan requires an interim approach that allows for a faster introduction of new services without requiring a network wide hot cutover. Which two services block functions meet these requirements? (Choose 2)

  

  A. IPv6 ISATAP tunnel termination point
  B. policy gateways
  C. GRE tunnel to the local Internet edge
  D. BGP route reflectors
  E. GET VPN key server
  A. IPv6 ISATAP tunnel termination point
  C. GRE tunnel to the local Internet edge

• Question 302:

  Which option describes an advantage of UDLD?

  A. It makes the port go immediately into the forwarding state after being connected.
  B. It prevents switch loops by detecting one-way communications on the physical port.
  C. It prevents switched traffic from traversing suboptimal paths on the network.
  D. It prevents switch loops caused by uni-directional point-to-point link condition on Rapid PVST+ and MST.
  E. It does not generate a spanning-tree topology change upon connecting and disconnecting a station on a port.
  F. It allows small, unmanaged switches to be plugged into ports of access switches without the risk of switch loops.
  B. It prevents switch loops by detecting one-way communications on the physical port.

• Question 303:

  Which markup language is used to format Ansible's playbook?

  A. ADML
  B. YAML
  C. XML
  D. HTML
  E. NAML
  B. YAML

• Question 304:

  The Customer X network consists of an MPLS core, IS-IS running as IGP, a pair of BGP route reflectors for route propagation, and a few dozens of MPLS-TE tunnels for specific tactical traffic engineering requirements. The customer engineering department has some

  QUESTION NO:s about the use of the Overload Bit in the IS-IS networks and how it could be used to improve their current network design. Which three options about the Overload Bit are true? (Choose three.)

  A. It is not recommended on BGP route reflectors.
  B. It only affects the use of the respective node as a transit node, and networks advertised within the LSPs of the node are still reachable.
  C. It can be set on a router during the startup process for a fixed period of time.
  D. It forces the midpoint MPLS-TE node to reoptimize the primary tunnels going through the OL node.
  E. It can be set on a router until other interacting protocols have signaled convergence.
  B. It only affects the use of the respective node as a transit node, and networks advertised within the LSPs of the node are still reachable.
  C. It can be set on a router during the startup process for a fixed period of time.
  E. It can be set on a router until other interacting protocols have signaled convergence.

• Question 305:

  Which statement about IDS/IPS design is correct?

  A. An IPS analyzes a copy of the monitored traffic and not the actual forwarded packet.
  B. An IPS should be deployed if the security policy does not support the denial of traffic.
  C. An IDS analyzes a copy of the monitored traffic and not the actual forwarded packet.
  D. Bandwidth considerations must be taken into account since IDS is deployed inline to traffic flow.
  C. An IDS analyzes a copy of the monitored traffic and not the actual forwarded packet.

• Question 306:

  Which feature must be part of the network design to wait a predetermined amount of time before notifying the routing protocol of a change in the path in the network?

  A. Transmit delay
  B. Throttle timer
  C. SPF hold time
  D. Interface dampening
  B. Throttle timer

• Question 307:

  Which two design aspects should a metro service provider consider when planning to deploy REP for his backbone? (Choose two.)

  A. Two REP segments can be connected redundantly at two points, one connection will be blocked as per the STP defined in IEEE 802.1d.
  B. UDLD can be enabled on REP interfaces to detect unidirectional failures.
  C. The guaranteed convergence recovery time is less than 50 ms for the local segment.
  D. A REP segment is limited to a maximum of seven devices.
  E. VLAN load balancing for optimal bandwidth usage is supported in any REP segment.
  B. UDLD can be enabled on REP interfaces to detect unidirectional failures.
  E. VLAN load balancing for optimal bandwidth usage is supported in any REP segment.

• Question 308:

  A company wants to connect two data center sites using a hub-and-spoke design with 2000 remote sites. One design consideration is the requirement to transfer MPLS packets over the public Internet. In addition, one router at each site should be used, and the MPLS packets must be encapsulated inside IP packets because the public Internet cannot transfer native MPLS packets. Which feature can be used to simplify the network design?

  A. GET VPN can be used to encrypt the MPLS packets with IPsec.
  B. DMVPN can be used to build up GRE tunnels dynamically with MPLS encapsulation inside.
  C. L2TPv3 can be used to encapsulate the MPLS packets.
  D. Site-to-site IPsec without GRE can be used to encapsulate the MPLS packets.
  E. PPPoE can be used to encapsulate the MPLS packets.
  B. DMVPN can be used to build up GRE tunnels dynamically with MPLS encapsulation inside.

• Question 309:

  A network design includes a long signaling delay in notifying the Layer 3 control plane that an interface has failed. Which two of these actions would reduce that delay? (Choose two.)

  A. Enable lower data link layer recovery systems to have an opportunity to restore the interface.
  B. Increase the notification of interface flaps.
  C. Reduce the time for the network to reconverge.
  D. Increase network stability.
  A. Enable lower data link layer recovery systems to have an opportunity to restore the interface.
  C. Reduce the time for the network to reconverge.

• Question 310:

  What is a characteristic of traffic shaping?

  A. It minimizes traffic transmission intervals.
  B. It remarks excess packets above the committed rates.
  C. It delays and can drop excess traffic.
  D. It classifies traffic based on certain characteristics.
  C. It delays and can drop excess traffic.