Cisco 351-080 Online Practice Questions and Exam Preparation

Cisco 351-080 Online Questions & Answers

• Question 301:

  Refer to the exhibit.

  

  Which statement about the exhibit is true?

  A. OTV does not extend STP across sites. Each site runs its own STP, rather than including all sites in a large STP domain. This topology also allows the use of different STP modes, such as PVRST+ or MST, in each site.
  B. OTV extends STP across sites. Each site runs its own STP, which includes all sites in a large STP domain. This topology also allows the use of different STP modes, such as PVRST+ or MST in each site.
  C. OTV does not extend STP across sites. Each site runs multiple STPs that include all sites in a large STP domain. This topology also allows the use of different STP modes, such as PerPVRST+ or MST, in each site.
  D. OTV extends STP across sites. Each site runs its own STP, which includes all sites in a large STP domain. This topology does not allow the use of different STP modes, such as PVRST+ or MST, in each site.
  A. OTV does not extend STP across sites. Each site runs its own STP, rather than including all sites in a large STP domain. This topology also allows the use of different STP modes, such as PVRST+ or MST, in each site.

• Question 302:

  Drag the terms on the left to the correct description on the right.

  Select and Place:

  

  

• Question 303:

  What is the purpose of the management interface monitoring policy?

  A. to monitor the management interface counters for errors and drops
  B. to prevent VM traffic from being black-holed during a cluster switchover
  C. to sync MAC address tables between peer fabric interconnects
  D. to ensure that the management interface of the managing fabric interconnect can reach the gateway
  D. to ensure that the management interface of the managing fabric interconnect can reach the gateway

• Question 304:

  Refer to the exhibit.

  

  Assume that the Cisco UCS 6200 Series Fabric Interconnects are equipped with 16 port expansion modules. What is the impact of the last command in the exhibit?

  A. Fabric interconnect B will reboot.
  B. The expansion module on fabric interconnect B will reload.
  C. The command will generate an error.
  D. Both fabric A and B expansion modules will reload.
  E. The expansion module on fabric interconnect B will reload according to the maintenance policy that is set by Cisco UCS Manager.
  C. The command will generate an error.

• Question 305:

  Which statement describes the FIP function of the FCoE Initiation Protocol?

  A. It is required to establish the point-to-point FCoE links with the first switch in the path.
  B. It is required to establish the point-to-point FCoE links with any switch across multiple Ethernet segments.
  C. It is not used to build the FCoE links.
  D. It is used to ensure lossless transport.
  B. It is required to establish the point-to-point FCoE links with any switch across multiple Ethernet segments.

• Question 306:

  Why is a Cisco UCS B250 server unable to support 16-GB DIMMs?

  A. Dual-rank DIMMs are not supported.
  B. 16-GB DIMMs are too slow.
  C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB.
  D. The memory bus would be too long.
  E. The blade would run too hot.
  C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB.

• Question 307:

  Drag Drop

  Select and Place:

  

  

• Question 308:

  FabricPath brings the benefits of routing protocols to Layer 2 network Ethernet environments. Which thee options describe advantages of using FabricPath technology? (Choose three.)

  A. MAC address scalability with conversational learning
  B. loop mitigation with TTL in the frame field
  C. Spanning Tree Protocol independence
  D. 10-Gb/s bandwidth
  E. Layer 2 extensions between data centers
  A. MAC address scalability with conversational learning
  B. loop mitigation with TTL in the frame field
  C. Spanning Tree Protocol independence

• Question 309:

  Your company wants Server 1/eth0 (vNIC 1) configured so that it always uses Fabric Interconnect A Port Channel 1 (Po1) when it communicates with anything outside of the Cisco UCS domain. However, if vNIC 1 fails over to Fabric Interconnect B using fabric failover, then vNIC 1 can use any uplink port on Fabric Interconnect B.

  Which statements are true? (Choose two.)

  A. The fabric interconnects must be in end-host mode.
  B. A pin group must be configured on the server tab in Cisco UCS Manager.
  C. In the service profile for Server 1, vNIC 1 must be explicitly assigned to a pin group.
  D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load- balancing algorithm.
  E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned, but not both.
  A. The fabric interconnects must be in end-host mode.
  C. In the service profile for Server 1, vNIC 1 must be explicitly assigned to a pin group.

• Question 310:

  Which two statements about the clear zone database vsan 2 command when performed on a Cisco Nexus 5500 switch are true? (Choose two.)

  A. Zone set for VSAN 2 is cleared from all switches in VSAN 2.
  B. The full zone set database is cleared for VSAN2 and the active zone set database for VSAN2 is untouched.
  C. This command is valid only if the feature clearzone is enabled.
  D. The active and full zone set for VSAN2 is deactivated and erased from the local switch.
  E. You must issue the copy running-config startup-config command to copy the active zone set database to the full zone set database after this command.
  A. Zone set for VSAN 2 is cleared from all switches in VSAN 2.
  C. This command is valid only if the feature clearzone is enabled.