Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 551:

  SIMULATION

  Guidelines

  This is a lab item in which tasks will be performed on virtual devices.

  1. Refer to the Tasks tab to view the tasks for this lab item.

  2. Refer to the Topology tab to access the device console(s) and perform the tasks.

  3. Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

  4. All necessary preconfigurations have been applied.

  5. Do not change the enable password or hostname for any device.

  6. Save your configurations to NVRAM before moving to the next item.

  7. Click Next at the bottom of the screen to submit this lab and move to the next question.

  8. When Next is clicked, the lab closes and cannot be reopened.

  Topology

  

  Tasks:

  

  A. See the solution below in Explanation.
  B. Place Holder
  C. Place Holder
  D. Place Holder
  A. See the solution below in Explanation.

  ---

  Explanation

  Sw10

  Config t

  no int po1

  default int ran et0/0-2

  int ran e0/0-2

  switchport trunk encap dot1q

  switchport mode trunk

  channel-group 1 mode active

  no shut

  

  

• Question 552:

  Refer to me exhibit.

  

  What is the cause of the log messages?

  A. hello packet mismatch
  B. OSPF area change
  C. MTU mismatch
  D. IP address mismatch
  B. OSPF area change

• Question 553:

  A network administrator is Implementing a routing configuration change and enables routing debugs to track routing behavior during the change. The logging output on the terminal is interrupting the command typing process.

  Which two actions can the network administrator take to minimize the possibility of typing commands incorrectly? (Choose two.)

  A. Configure the logging synchronous global configuration command
  B. Configure the logging delimiter feature
  C. Configure the logging synchronous command under the vty
  D. Press the TAB key to reprint the command in a new line
  E. increase the number of lines on the screen using the terminal length command
  C. Configure the logging synchronous command under the vty
  D. Press the TAB key to reprint the command in a new line

• Question 554:

  Refer to the exhibit

  

  The network administrator must be able to perform configuration changes when all the RADIUS servers are unreachable. Which configuration allows all commands to be authorized if the user has successfully authenticated?

  A. aaa authorization exec default group radius none
  B. aaa authentication login default group radius local none
  C. aaa authorization exec default group radius if-authenticated
  D. aaa authorization exec default group radius
  C. aaa authorization exec default group radius if-authenticated

  ---

  Explanation

  The keyword"if-authenticated" sayings that if we are authenticated we will immediately be dropped into exec (enable) mode.

• Question 555:

  Refer to me exhibit.

  

  The NETCONF object is sent to a Cisco IOS XE switch. What is me purpose of the object?

  A. View the configuration of all GigabitEthernet interfaces
  B. Discover the IP address of interface GigabitEthernet1
  C. Set the description of interface GigabitEthernet1 to "1"
  D. Remove the IP address from interface GigabitEthernet1
  A. View the configuration of all GigabitEthernet interfaces

• Question 556:

  What is an emulated machine that has dedicated compute, memory, and storage resources and a fully installed operating system?

  A. host
  B. mainframe
  C. container
  D. virtual machine
  D. virtual machine

  ---

  Explanation

  Mainframe + Host are Hardware Devices and they do not EMULATE but rather EXECUTE.

  Virtual Machine is the only "EMULATION" capable thing in the list.

  A container is a software wrapper that allows programs to run inside it, but itself it still needs to be executed and not emulated.

• Question 557:

  Which characteristic applies to the endpoint security aspect of the Cisco Threat Defense architecture?

  A. detect and block ransomware in email attachments
  B. outbound URL analysis and data transfer controls
  C. user context analysis
  D. blocking of fileless malware in real time
  D. blocking of fileless malware in real time

• Question 558:

  Refer to the exhibit.

  

  What is achieved by this Python script?

  A. It displays the output from show lldp neighbors into a standard output.
  B. It reads the neighbor count from show lldp neighbors into a dictionary list.
  C. It displays the Layer 3 neighbors from show lldp neighbors on the terminal screen.
  D. It reads the output from show lldp neighbors into an array object.
  B. It reads the neighbor count from show lldp neighbors into a dictionary list.

• Question 559:

  Refer to the exhibit.

  

  Which type of antenna is shown on the radiation patterns?

  A. Yagi
  B. dipole
  C. patch
  D. omnidirectional
  A. Yagi

• Question 560:

  Why would a network engineer configure an AP in SE-Connect mode?

  A. to redirect WLAN traffic to an endpoint for protocol analysis
  B. to monitor the VLAN traffic for rogue APs
  C. to connect the wired LAN with the wireless infrastructure
  D. to analyze the RF spectrum surrounding the AP
  A. to redirect WLAN traffic to an endpoint for protocol analysis