Cisco 350-401 Online Practice Questions and Exam Preparation

Cisco 350-401 Online Questions & Answers

• Question 1271:

  DRAG DROP

  Drag and drop the Cisco DNA Center northbound API characteristics from the left to the right. Not all options are used.

  Select and Place:

  

  

• Question 1272:

  Which action limits the total amount of memory and CPU that is used by a collection of VMs?

  A. Place the collection of VMs in a resource pool.
  B. Place the collection of VMs in a vApp.
  C. Limit the amount of memory and CPU that is available to the cluster.
  D. Limit the amount of memory and CPU that is available to the individual VMs.
  A. Place the collection of VMs in a resource pool.

• Question 1273:

  An engineer has deployed a single Cisco 5520 WLC with a management IP address of 172.16.50.5/24. The engineer must register 50 new Cisco AIR-CAP2802I-E-K9 access points to the WLC using DHCP option 43. The access points are connected to a switch in VLAN 100 that uses the 172.16.100.0/24 subnet. The engineer has configured the DHCP scope on the switch as follows:

  

  The access points are failing to join the wireless LAN controller. Which action resolves the issue?

  A. configure option 43 Hex F104.AC10.3205
  B. configure option 43 Hex F104.CA10.3205
  C. configure dns-server 172.16.50.5
  D. configure dns-server 172.16.100.1
  A. configure option 43 Hex F104.AC10.3205

  ---

  Explanation

  172.16.50.5 in hex is We will have the answer from this paragraph: "TLV values for the Option 43 suboption: Type + Length + Value. Type is always the suboption code 0xf1. Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex. For example, suppose there are two controllers with management interface IP addresses, 192.168.10.5 and 192.168.10.20. The type is 0xf1. The length is 2 * 4 = 8 = 0x08. The IP addresses translates to c0a80a05 (192.168.10.5) and c0a80a14 (192.168.10.20). When the string is assembled, it yields f108c0a80a05c0a80a14. The Cisco IOS IT Certification Guaranteed, The Easy Way! 81command that is added to the DHCP scope is option 43 hex f108c0a80a05c0a80a14." Reference: Click Therefore in this question the option 43 in hex should be "F104.AC10.3205 (the management IP address of 172.16.50.5 in hex is AC.10.32.05).

• Question 1274:

  Refer to the exhibit.

  

  Which configuration must be added to enable remote access only using SSHv1 or SSHv2 to this router?

  

  A. Option A
  B. Option B
  C. Option C
  D. Option D
  B. Option B

• Question 1275:

  What is the main function of VRF-lite?

  A. To connect different autonomous systems together to share routes
  B. To allow devices to use labels to make Layer 2 Path decisions
  C. To route IPv6 traffic across an IPv4 backbone
  D. To segregate multiple routing tables on a single device
  D. To segregate multiple routing tables on a single device

• Question 1276:

  Refer to the exhibit.

  

  How was spanning-tree configured on this interface?

  A. By entering the command spanning-tree portfast trunk in the interface configuration mode.
  B. By entering the command spanning-tree portfast in the interface configuration mode.
  C. By entering the command spanning-tree mst1 vlan 10,20,30,40 in the global configuration mode.
  D. By entering the command spanning-tree vlan 10,20,30,40 root primary in the interface configuration mode.
  A. By entering the command spanning-tree portfast trunk in the interface configuration mode.

• Question 1277:

  Which of the following are valid Port Aggregation Protocol (PAgP) modes? (Choose two.)

  A. On
  B. Active
  C. Passive
  D. Auto
  E. Desirable
  D. Auto
  E. Desirable

• Question 1278:

  Refer to the exhibit.

  

  The OSPF neighborship fails between two routers. What is the cause of this issue?

  A. The OSPF router ID is missing on this router.
  B. The OSPF process is stopped on the neighbor router.
  C. There is an MTU mismatch between the two routers.
  D. The OSPF router ID is missing on the neighbor router.
  C. There is an MTU mismatch between the two routers.

  ---

  Explanation

  Stuck in ExStart and jumbo points to MTU.

  cisco_R2(config-subif)#do debug ip osp adj OSPF adjacency debugging is on cisco_R2(config-subif)#ip mtu 1111 <<<<<<<<<<<<<<<< cisco_R2(config-subif)# cisco_R2(config-subif)# cisco_R2(config-subif)#do clear ip ospf

  !!!debug shows this:

  cisco_R2(config-subif)#

  *Dec 23 13:02:27.164: OSPF-1 ADJ Et0/0.10: Rcv DBD from 6.6.6.6 seq 0x19FD opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART <<<<<<<<<<<<< *Dec 23 13:02:27.164: OSPF-1 ADJ Et0/0.10: Nbr 6.6.6.6 has larger interface MTU <<<<<<<<<

  *Dec 23 13:02:27.164: OSPF-1 ADJ Et0/0.10: Rcv DBD from 6.6.6.6 seq 0x26B opt 0x52 flag 0x2 len 112 mtu 1500 state EXSTART

  *Dec 23 13:02:27.164: OSPF-1 ADJ Et0/0.10: Nbr 6.6.6.6 has larger interface MTU *Dec 23 13:02:27.395: OSPF-1 ADJ Et0/0.10: Rcv DBD from 6.6.6.6 seq 0x26B opt 0x52 flag 0x2 len 112 mtu 1500 state EXSTART

• Question 1279:

  DRAG DROP

  Drag and drop the characteristics from the left onto the orchestration tools that they describe on the right.

  Select and Place:

  

  

• Question 1280:

  Which HTTP status code is the correct response for a request with an incorrect password applied to a REST API session?

  A. HTTP Status Code: 200
  B. HTTP Status Code: 302
  C. HTTP Status Code: 401
  D. HTTP Status Code: 504
  C. HTTP Status Code: 401

  ---

  Explanation

  https://developer.mozilla.org/en-US/docs/Web/HTTP/Status/401