Cisco 350-050 Online Practice Questions and Exam Preparation

Cisco 350-050 Online Questions & Answers

• Question 171:

  Refer to the exhibit.

  

  A network administrator is configuring and installing an indoor mesh network using two CAPWAP APs. The APs were out of the box and have already been installed in their designated locations. The RAP is joined to the controller and configured appropriately, but the MAP is not visible on the WLC. In the output shown, which of these explanations is the most likely reason for the issue?

  A. The MAP should have been primed to the WLC before being deployed. The Bridge Group Name is not configured by default. The AP policy for the MAP is not configured.
  B. The MAP should have been primed to the WLC before being deployed. The Bridge Group Name uses the MAC address and is configured but does not match, which is the reason for the failure.
  C. The MAP does not have to be primed to the WLC before being deployed to the field because the WLC discovery process is different for MAPs than it is for RAPs. The Bridge Group Name does not have to match but the RAP has to have the MAP MAC address added to its database.
  D. The MAP should have been primed to the WLC before being deployed. The Bridge Group Name does not need to match. The MAP is running an LWAPP image that requires its MAC address to be configured in the RAP in order for a successful join.
  E. The MAP does not have to be primed to the WLC before being deployed. The Bridge Group Name needs to match. The AP policy is automatically populated by the MAP discovery process via CAPWAP, but is failing in this example.
  A. The MAP should have been primed to the WLC before being deployed. The Bridge Group Name is not configured by default. The AP policy for the MAP is not configured.

• Question 172:

  Which statement about the beamforming (ClientLink) feature on the Cisco WLC is true?

  A. It works only with 802.11n APs and clients.
  B. It works only with 802.11n APs and 802.11b/g clients.
  C. It provides a signal gain when the AP transmits towards the client.
  D. It provides a signal gain in both directions (AP to client and client to AP).
  C. It provides a signal gain when the AP transmits towards the client.

• Question 173:

  You need to deploy several WLCs to manage Unified APs on the main site and on remote locations (on different subnets). A wireless network printer is added to the network. Multicast is used to discover the printer. You enable multicastmulticast mode on the WLCs. Which two of these statements are true, considering interoperability and requirements of the network? (Choose two.)

  A. The infrastructure should be ready to allow multicast routing from the WLC management interfaces to all managed APs.
  B. There is no need to configure multicast routing on the infrastructure, because all the wireless clients are on the same VLAN or subnet.
  C. You can configure any multicast IP address on the WLCs, as long as you make sure to use the same address on the WLCs.
  D. To avoid issues, you need to make sure that the WLC multicast IP address is different for each controller and is not used for anything else on the network.
  E. There is no need to allow multicast traffic on the WAN VPN links to the remote locations, because this traffic goes within the LWAPP/CAPWAP tunnel.
  A. The infrastructure should be ready to allow multicast routing from the WLC management interfaces to all managed APs.
  D. To avoid issues, you need to make sure that the WLC multicast IP address is different for each controller and is not used for anything else on the network.

• Question 174:

  Which three of these options are not valid ways to extend wireless coverage in an autonomous AP environment? (Choose three.)

  A. Add additional APs in repeater mode.
  B. Add additional APs in bridge mode.
  C. Add additional APs in access point mode.
  D. Increase the transmitter power level.
  E. Use both radios.
  F. Position the APs optimally.
  G. Use QoS.
  B. Add additional APs in bridge mode.
  E. Use both radios.
  G. Use QoS.

• Question 175:

  On a Cisco WLC, which NTP authentication type or types are supported?

  A. MD5 and DES
  B. MD5, DES, and DES-CBC
  C. MD5
  D. DES
  E. DES-CBC
  C. MD5

• Question 176:

  After interviewing a customer to understand wireless client requirements, you determine that 802.11b must be enabled to support legacy clients within a mixed-mode environment. Which recommendation will have the greatest impact on mitigating the effects of 802.11b clients on the rest of the network?

  A. Restrict OFDM modulation from being used.
  B. Make 11 Mb/s the lowest mandatory rate.
  C. Enable a separate SSID for 802.11b clients.
  D. Enable a short preamble.
  B. Make 11 Mb/s the lowest mandatory rate.

• Question 177:

  Which statement about using the internal DHCP server feature on a Cisco WLC is true?

  A. DHCP option 43 must be configured on the internal DHCP server.
  B. The DHCP server IP address must be set to the Cisco WLC management interface IP address.
  C. The internal DHCP server can serve both wireless and wired clients.
  D. Autonomous APs are supported.
  B. The DHCP server IP address must be set to the Cisco WLC management interface IP address.

• Question 178:

  The IT administrator can confirm the air quality and existing non-Wi-Fi interference on the Cisco WLC but cannot find any non-Wi-Fi interference on the Cisco WCS. What are two possible reasons for this issue? (Choose two.)

  A. The administrator did not add Cisco MSE to Cisco WCS.
  B. The administrator added Cisco MSE to Cisco WCS but forgot to sync Cisco MSE with Cisco WLC and the floor map.
  C. The administrator needs to enable the CleanAir function from the Cisco WCS GUI again.
  D. The administrator needs to restart Cisco WCS after adding Cisco WLC, to enable the CleanAir function.
  A. The administrator did not add Cisco MSE to Cisco WCS.
  B. The administrator added Cisco MSE to Cisco WCS but forgot to sync Cisco MSE with Cisco WLC and the floor map.

• Question 179:

  When adding an MSE to a Cisco WCS, you are given the option to enable HTTP. What would be a good reason to enable HTTP communication to the MSE?

  A. If HTTPS is disabled on the MSE.
  B. If port 443 is blocked by a firewall in between WCS and the MSE.
  C. If the MSE is being added to a version of WCS prior to 7.0.
  D. If a a third-party application needs to communicate with the MSE.
  D. If a a third-party application needs to communicate with the MSE.

• Question 180:

  Refer to the exhibit.

  

  Which method was used to define this rogue AP as malicious?

  A. This rogue AP matched a WCS malicious rogue AP classification rule.
  B. A WCS switch port trace was performed and the MAC address of the rogue AP was found connected to a Cisco switch port.
  C. This rogue AP was discovered using RLDP.
  D. A rogue AP alert was enabled that defines all rogues with open SSIDs as malicious.
  D. A rogue AP alert was enabled that defines all rogues with open SSIDs as malicious.