Cisco 350-050 Online Practice Questions and Exam Preparation

Cisco 350-050 Online Questions & Answers

• Question 1:

  DRAG DROP

  Select and Place:

  

  

• Question 2:

  You want to prevent a wireless client with a MAC address of 00:40:96:a5:b5:d4 from associating with an autonomous AP. Which commands do you use on the autonomous AP?

  A. dot11 association mac-list 700 access-list 700 deny 0040.96a5.b5d4 ffff.ffff.ffff
  B. dot11 association mac-list 700 access-list 700 permit 0000.0000.0000 ffff.ffff.ffff access-list 700 deny 0040.96a5.b5d4 0000.0000.0000
  C. dot11 association mac-list 700 access-list 700 deny 0040.96a5.b5d4 0000.0000.0000 access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
  D. dot11 association mac-list 700 access-list 700 deny 0040.96a5.b5d4 ffff.ffff.ffff access-list 700 permit 0000.0000.0000 ffff.ffff.ffff
  E. none of the above
  C. dot11 association mac-list 700 access-list 700 deny 0040.96a5.b5d4 0000.0000.0000 access-list 700 permit 0000.0000.0000 ffff.ffff.ffff

• Question 3:

  In order to protect IEEE 802.11 clients against spoofed management frames, client Management Frame Protection encrypts management frames sent between access points and clients. Which three of these management frames are protected by client MFP? (Choose three.)

  A. beacon
  B. authentication
  C. deauthentication
  D. disassociation
  E. probe request
  F. probe response
  G. QoS (WMM) action frames
  C. deauthentication
  D. disassociation
  G. QoS (WMM) action frames

• Question 4:

  After a scheduled downtime of your 5508 WLC, you notice that only a handful of the 100 APs are rejoining the controller. All the APs are in the same subnet and use default settings. Cisco WLC debugs indicate that the APs are sending discovery and join requests. Only after shutting down all the switch ports that connect to the APs and turning five ports back on at a time can you rejoin all the APs. Why were the APs unable to rejoin the Cisco WLC, and how can you prevent this from happening in the future?

  A. Having all the APs in the same VLAN created a Layer 2 broadcast storm, preventing the APs from receiving discovery and join responses from the Cisco WLC. You can prevent this by configuring the APs to send syslog messages to a multicast address, using the Cisco WLC CLI only.
  B. Having all the APs in the same VLAN created a Layer 2 broadcast storm, preventing the APs from receiving discovery and join responses from the Cisco WLC. You can prevent this by configuring the APs to send syslog messages to a unicast address, using the Cisco WLC CLI only.
  C. Having all the APs in the same VLAN created a Layer 3 broadcast storm, preventing the APs from receiving discovery and join responses from the Cisco WLC. You can prevent this by configuring the APs to send syslog messages to a unicast address, using the Cisco WLC CLI only.
  D. Having all the APs in the same VLAN created a Layer 2 broadcast storm. You cannot prevented this from happening again.
  B. Having all the APs in the same VLAN created a Layer 2 broadcast storm, preventing the APs from receiving discovery and join responses from the Cisco WLC. You can prevent this by configuring the APs to send syslog messages to a unicast address, using the Cisco WLC CLI only.

• Question 5:

  Refer to the exhibit.

  

  The corporate office has mandated that all guest WLAN users should have a per-user bandwidth restriction. The requirement is 1 Mb/s for normal rate with a peak of 1.2 Mb/s. This is to be set for HTTP traffic only. From the exhibit, showing the QoS properties for a current guest user connection, is the above requirement met?

  A. Yes, the profile has been configured for 1000 Kb/s for average rate and 1200 Kb/s for burst rate for all traffic.
  B. No, the profile has been configured for 1000 Mb/s for average rate and 1200 Mb/s for burst rate for HTTP traffic.
  C. No, the profile has been configured for 1000 Kb/s for average rate and 1200 Kb/s for burst rate for all traffic.
  D. Yes, the profile has been configured for 1000 Kb/s for average rate and 1200 Kb/s for burst rate for HTTP traffic.
  E. Yes, the profile has been configured for 1000 Mb/s for average rate and 1200 Mb/s for burst rate for all traffic.
  C. No, the profile has been configured for 1000 Kb/s for average rate and 1200 Kb/s for burst rate for all traffic.

• Question 6:

  Which three of these options are variables used within the TPC algorithm to determine the transmit power? (Choose three.)

  A. antenna gain (dBi)
  B. antenna gain (dBm)
  C. RSSI of third highest neighbor above the threshold
  D. SNR of third highest neighbor above the threshold
  E. Tx power control threshold
  F. client SNR cutoff value
  G. number of neighbors
  H. Tx Max
  C. RSSI of third highest neighbor above the threshold
  E. Tx power control threshold
  H. Tx Max

• Question 7:

  Which regulatory body develops standards for European information and communication technologies?

  A. European Union
  B. European Telecommunications Standards Institute
  C. European Radio and Telecommunications Terminal Equipment Directive
  D. International Organization for Standardization
  B. European Telecommunications Standards Institute

• Question 8:

  Which role does the Wi-Fi Alliance fulfill regarding WLANs?

  A. creates global interoperability for wireless channels and spectrum
  B. maintains and creates the protocol standards by which wireless devices work
  C. ensures that wireless products that are available to consumers provide the features that the products claim to have
  D. creates strict regulations
  C. ensures that wireless products that are available to consumers provide the features that the products claim to have

• Question 9:

  Which debug command is best to use when you suspect that a client will not connect to an autonomous AP because of an incorrect WPA PSK?

  A. debug dot11 mgmt station
  B. debug dot11 aaa authenticator process
  C. debug dot11 station connection failure
  D. debug dot11 encryption
  C. debug dot11 station connection failure

• Question 10:

  You are configuring WLC high availability for an access point. Which statement is true?

  A. You always need to configure both the controller system names and WLC IP address.
  B. High availability can only be configured using the WLC IP addresses.
  C. Controller names in access point high availability configurations are not case-sensitive.
  D. A WLC IP address only needs to be configured when the backup WLC is in a different mobility group.
  D. A WLC IP address only needs to be configured when the backup WLC is in a different mobility group.