Cisco 300-115 Online Practice Questions and Exam Preparation

Cisco 300-115 Online Questions & Answers

• Question 1011:

  Question about how to disable cdp. (Choose two)

  A. (config) no cdp run
  B. (config) cdp disable
  C. (config-if) no cdp enable
  D. (config-if) no cdp run
  E. (config-if) cdp disable
  F. (config) no cdp enable
  A. (config) no cdp run
  C. (config-if) no cdp enable

• Question 1012:

  Which two statements about error-disabled ports are true? (Choose two.)

  A. When a port is error-disabled, it may continue to pass management traffic.
  B. When a port is error-disabled, all traffic on the port stops.
  C. By default, error-disabled ports automatically recover once the issue is resolved
  D. When a port is error-disabled, the port LED changes to solid orange.
  E. They can be recovered only by resetting the interface.
  B. When a port is error-disabled, all traffic on the port stops.
  D. When a port is error-disabled, the port LED changes to solid orange.

• Question 1013:

  Refer to the exhibit. Which two effects of this configuration are true? (Choose two.)

  

  A. R1 becomes the active router.
  B. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online
  C. Hello messages are sent to multicast address 224.0.0.5.
  D. If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online.
  E. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online
  F. R1 becomes the standby router.
  A. R1 becomes the active router.
  E. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online

• Question 1014:

  Which two statements about MAC address learning are true? (choose two)

  A. it must be disabled on SVIs
  B. it can be disabled globally and then reactivated on selected VLANs
  C. it can be disabled only on nonmanagement interfaces
  D. the administrator must disable MAC address learning only on VLANs with exactly two ports
  E. it can be disabled only on secure ports
  B. it can be disabled globally and then reactivated on selected VLANs
  D. the administrator must disable MAC address learning only on VLANs with exactly two ports

• Question 1015:

  A question about port number and multicast address of HSRP. (CONCEPT ONLY)

  A. HSRP uses multicast address 224.0.0.2 and uses UDP port 1985
  A. HSRP uses multicast address 224.0.0.2 and uses UDP port 1985

• Question 1016:

  Enablement of which feature puts the port into err-disabled state when the port has PortFast enabled and it receives BPDUs?

  A. BPDU filtering
  B. BackboneFast
  C. EtherChannel
  D. BPDU guard
  D. BPDU guard

• Question 1017:

  When a Layer 2 EtherChannel is configured, which statement about interaction with the Spanning Tree Protocol is true?

  A. Spanning Tree uses only the member ports for forwarding.
  B. Spanning Tree uses the port channel for forwarding.
  C. Spanning Tree uses the port channel and member ports for forwarding.
  D. Spanning Tree does not use port channels in loop prevention
  B. Spanning Tree uses the port channel for forwarding.

• Question 1018:

  Drag and Drop

  Select and Place:

  

  

• Question 1019:

  What is the value of the TPID/tag protocol identifier of QinQ?

  A. 0x8a88
  B. 0x8100
  C. 0x8b45
  D. 0x8200
  A. 0x8a88

• Question 1020:

  Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.

  

  Examine the VTP configuration. You are required to configure private VLANs for a new server deployment connecting to the SW4 switch. Which of the following configuration steps will allow creating private VLANs?

  A. Disable VTP pruning on SW1 only
  B. Disable VTP pruning on SW2 only
  C. Disable VTP pruning on SW4 only
  D. Disable VTP pruning on SW2, SW4 and New_Switch
  E. Disable VTP pruning on New_Switch and SW4 only.
  C. Disable VTP pruning on SW4 only

  ---

  To create private VLANs, you will need to only disable pruning on the switch that contains the private VLANs. In this case, only SW4 will connect to servers in a private VLAN.