Cisco 300-080 Online Practice Questions and Exam Preparation

Cisco 300-080 Online Questions & Answers

• Question 161:

  Users report intermittent call failures. All calls must invoke an IOS-based transcoder, registered to Cisco Unified Communications Manager, to be successful. Which two commands can be used to rule out issues with the transcoder? (Choose two.)

  A. debug voip ccapi inout
  B. debug ccsip message
  C. show dspfarm profile
  D. show version
  E. debug sccp messages
  A. debug voip ccapi inout
  B. debug ccsip message

• Question 162:

  You cannot dial a number, but the endpoint is registered. Which of these actions must you do first?

  A. Check the call log of the endpoint you are trying to dial
  B. Identify the numbers, partitions, and search spaces, the generate a route plan report in Cisco Unified Communications Manager Administration and use it to examine all the route patterns for the partitions that are in the calling search space for the problem call
  C. Check the call log of the originating endpoint in the call
  D. Go to Cisco Unified Communications Manager > Diagnostics > Call Logs and run a call log to check where the call is going
  B. Identify the numbers, partitions, and search spaces, the generate a route plan report in Cisco Unified Communications Manager Administration and use it to examine all the route patterns for the partitions that are in the calling search space for the problem call

• Question 163:

  Which two troubleshooting tools would initially be the best to use when troubleshooting the PSTN gateway side of a call routing issue while using Cisco Unified Communications Manager? (Choose two.)

  A. RTMT trace output
  B. Cisco IOS debug commands
  C. Dialed Number Analyzer output
  D. Cisco Unified Communications Manager alerts
  E. Cisco IOS show commands
  B. Cisco IOS debug commands
  E. Cisco IOS show commands

• Question 164:

  You install a second Cisco TelePresence PrecisionHD 1080p camera on your C-Series Codec, but you are unable to control the camera. What should you do to fix this issue?

  A. Ensure that the distance between the end user and the camera is between 4 feet and 6 feet.
  B. Purchase and install a camera with full pan, tilt, and zoom capabilities.
  C. Order a VISCA cascading cable from Cisco, which connects the first camera to the second camera.
  D. Ensure that the RJ45 end of the camera cable goes to the connector that is marked "HD Video Out Codec."
  E. Ensure that the HD-SDI cable between the codec and the camera is not longer than 100 meters (330 feet).
  C. Order a VISCA cascading cable from Cisco, which connects the first camera to the second camera.

• Question 165:

  An engineer is attempting to troubleshoot issues with SAF and wants to understand what patterns are being discovered from SAF. Where does the engineer find this information?

  A. in Cisco Unified CM under Call Routing > Route Plan Report
  B. in RTMT under Reports > Learned Patterns
  C. in RTMT Under Reports > Route Plan
  D. in Cisco Unified CM under Call Routing > Call Control Discovery > Advertising Service
  B. in RTMT under Reports > Learned Patterns

• Question 166:

  You are troubleshooting video quality issues on a Cisco TelePresence TX9000 Series system.

  Which CLI command shows the total number of lost video packets and the received jitter during a call in progress?

  A. show call statistics video
  B. show call statistics all
  C. show call statistics detail
  D. show call statistics video detail
  D. show call statistics video detail

• Question 167:

  While you deploy SAF CCD in a remote location, you are unable to enable the SAF CCD service on an Cisco IOS-based device. Which action can you take to troubleshoot the problem?

  A. Verify that Cisco Unity Express is operational.
  B. Verify that IOS Release 15.0(1)M is installed.
  C. Verify that DSP Farm resources are configured on the device.
  D. Verify that the device has sufficient RAM to run SAF CCD.
  E. Verify the integrity of the flash installation.
  A. Verify that Cisco Unity Express is operational.

• Question 168:

  To maintain proper database integrity, what is the recommended maximum round-trip delay between multiple Cisco VCS appliances in a cluster?

  A. 10 ms
  B. 15 ms
  C. 25 ms
  D. 30 ms
  E. 50 ms
  F. 80 ms
  D. 30 ms

• Question 169:

  Refer to the exhibit. What does this trace indicate?

  

  A. a disconnected call
  B. a completed call setup
  C. a failed call setup
  D. an interrupted call setup
  B. a completed call setup

• Question 170:

  In a Cisco Unified communications Manager Call trace, which string indicates an intra-site call?

  A. OutsideDialtone = [1]
  B. cmDeviceType = [Access Device]
  C. OutsideDialtone = [0]
  D. OutsideDialtone = [2]
  C. OutsideDialtone = [0]