Cisco 300-070 Online Practice Questions and Exam Preparation

Cisco 300-070 Online Questions & Answers

• Question 261:

  A phone is assigned to a partition that is included in the CSS HQ-Phone. This partition contains a route pattern to block calls to service numbers 1-400-xxx-xxxx. When the engineer makes a test call to the number 1-400-400-9000 from that phone, the call goes through. What is the reason for this issue?

  A. The route pattern for the number to be blocked is in partition not accessible to the CSS.
  B. The correct route list is not selected in the route pattern for the dialed number to be blocked.
  C. The correct gateway is not selected for the route list for the route pattern for the dialed number to be blocked.
  D. The route pattern for the number to be blocked is in "NULL" partition.
  E. The route pattern is misconfigured.
  A. The route pattern for the number to be blocked is in partition not accessible to the CSS.

• Question 262:

  Which three statements about the default VoIP dial peer are true? (Choose three.)

  A. VAD is disabled.
  B. RSVP is not supported.
  C. Only the G.711 codec is supported.
  D. The G.729 and G.711 codecs are supported.
  E. Fax-rate service is supported.
  F. DTMF relay is supported.
  B. RSVP is not supported.
  C. Only the G.711 codec is supported.
  E. Fax-rate service is supported.

• Question 263:

  Employees at a company must dial 9 first to reach an external number. Which route pattern is used to route the call if a user dials the toll-free number 1-866-555-1212?

  A. 9.18XX[2-9]XXXXXX
  B. 9.18[0,5-8][0,5-8]XXXXXXX
  C. 9.1XXXXXXXXXX
  D. 9.1866XXXXXXX
  E. 9.1866[2-9]XXXXXX
  F. 9.1[2-9]XX[2-9]XXXXXX
  E. 9.1866[2-9]XXXXXX

• Question 264:

  What is the correct order for configuring call routing in Cisco Unified Communications Manager?

  A. gateway and SIP trunk, route group, route pattern, route list
  B. gateway and SIP trunk, route list, route group, route pattern
  C. gateway and SIP trunk, route group, route list, route pattern
  D. route list, gateway and SIP trunk, route group, route pattern
  C. gateway and SIP trunk, route group, route list, route pattern

• Question 265:

  By default, what value is voice traffic marked as on a Cisco Catalyst Switch?

  A. DSCP CAS6 value 21, Cos 3
  B. DSCP AF21 value 46, Cos 5
  C. DSCP EF value 46, Cos 7
  D. DSCP EF value 46, Cos 5
  D. DSCP EF value 46, Cos 5

• Question 266:

  Which four modes are available on the Cisco TelePresence MCU MSE 8510 to connect to a gatekeeper? (Choose four.)

  A. direct mode
  B. H.225-routed mode
  C. H.265-routed mode
  D. H.245-routed mode
  E. full proxy mode
  F. partial proxy mode
  A. direct mode
  B. H.225-routed mode
  D. H.245-routed mode
  E. full proxy mode

• Question 267:

  An engineer is modifying a dial plan for a Cisco Unified Communications Manager system and notices that the new route patterns are not properly manipulating the dial string. Which configuration element must the engineer check to determine the cause?

  A. phone
  B. route list
  C. dial peer
  D. phone DN
  C. dial peer

• Question 268:

  In a multisite deployment, which two voice codecs are recommended to use between intrasite endpoints? (Choose two.)

  A. G.711
  B. G.728
  C. H.264
  D. G.722
  E. G.729
  A. G.711
  D. G.722

• Question 269:

  Which two options are available when configuring a POTS dial peer? (Choose two.)

  A. preference
  B. voice-class codec
  C. VAD
  D. answer-address
  E. codec
  A. preference
  D. answer-address

• Question 270:

  Which two options list the transcoder types that Cisco Unified Communications Manager supports?

  A. PLDM and SER Termination Point
  B. IOS and media termination point software and hardware
  C. IOS enhanced media termination point and WS-SVC-CMM
  D. virtual media termination point and codec termination point
  E. transcoding and ISR termination point
  C. IOS enhanced media termination point and WS-SVC-CMM
  E. transcoding and ISR termination point