Cisco 300-070 Online Practice Questions and Exam Preparation

Cisco 300-070 Online Questions & Answers

• Question 281:

  Time-of-day routing in Cisco Unified Communications Manager is configured in which of these ways?

  A. by specifying a time schedule on the phone device CSS
  B. by specifying a time period on the phone device CSS
  C. by specifying a time schedule on the partition that is being used for time-of-day routing
  D. by specifying a time period on the partition that is being used for time-of-day routing
  E. directly on the route pattern using an explicit timetable
  C. by specifying a time schedule on the partition that is being used for time-of-day routing

• Question 282:

  When configuring CUCM digit manipulation for calls on a gateway, which two do you use for prefixing digits on outgoing calls? (Choose two.)

  A. *
  B. \
  C. !
  D. =
  E. 0-9
  C. !
  E. 0-9

• Question 283:

  The abc.com Lumber Company would like to use AAR to reroute calls made from HQ to remote locations when those calls are rejected by the IP WAN because of insufficient bandwidth. The abc.com Lumber Company uses 5-digit dialing to

  all locations.

  abc.com Headquarters has a DID range from 770-555-0001 to 770-557-0500 and the Macon facility has a DID range from 912-556-0500 to 912-556-0550.

  How should the external phone masks be configured?

  A. 770557XXXX
  B. 9125560XXX
  C. 770555XXXX
  D. 77055XXXXX
  D. 77055XXXXX

• Question 284:

  Refer to Exhibit: If the user at extension 1001 dials the user at extension 2111, which dial peer is used to route the call?

  

  A. 3
  B. 2
  C. 4
  D. 1
  D. 1

• Question 285:

  How does Cisco Unified Communications Manager perform digit analysis?

  A. Use a set of route lists and filters to match all collected digits of a dialed number.
  B. Perform a digit-by-digit analysis to find the best matching route pattern based on a devices partition.
  C. Perform a digit-by-digit analysis to find the best matching route pattern within the partition list in the calling search space of a device.
  D. Send all collected digits through the Dialed Number Analyzer to determine the best call routing match within Cisco Unified CM.
  D. Send all collected digits through the Dialed Number Analyzer to determine the best call routing match within Cisco Unified CM.

• Question 286:

  Which type of dial plan implements destinations by using a format that is similar to email addresses?

  A. H.323
  B. E.164
  C. DNS
  D. URI
  D. URI

• Question 287:

  What is the default option for framing when you configure T1 controller?

  A. Super Frame
  B. alternate mark inversion
  C. Extended Super Frame
  D. cyclic redundancy check 4
  E. high-density bipolar 3
  F. No-CRC4
  G. binary 8-zero substitution
  H. Australia
  C. Extended Super Frame

• Question 288:

  Which purpose of the Dialed Number Analyzer within Cisco Unified Communications Manager is true?

  A. It provides a way to retrieve only the called number when examining CDR logs.
  B. It is used as a troubleshooting tool as it provides an efficient way to analyze the dial plan.
  C. It allows the administrator to see the dialed number (DNIS) of a call in real time as the call is being placed.
  D. It helps sort and analyze CDR logs.
  B. It is used as a troubleshooting tool as it provides an efficient way to analyze the dial plan.

• Question 289:

  Through which two configurations, in Cisco Unified Communications Manager, are inbound and outbound calls routed, respectively?

  A. inbound CSS and device pools
  B. route lists and outgoing CSS
  C. inbound CSS and route groups
  D. route patterns and outgoing CSS
  D. route patterns and outgoing CSS

• Question 290:

  Which three of these are characteristics of a Cisco Unified Communications Manager software- based Media Termination Point? (Choose three.)

  A. The codec and packetization of both call legs must be identical.
  B. This Media Termination Point type does not require any DSP resources on the Cisco router.
  C. DSP resources are required.
  D. It can provide G.711 mu-law to G.711 a-law conversion and vice versa.
  E. It can provide packetization conversion for a given codec (for example, if one call leg is using a 20-ms sample size, but the other call leg is using a 30-ms sample size).
  F. This Media Termination Point type is typically used for RSVP agent configurations or Cisco Unified Border Element media flow-through configurations.
  B. This Media Termination Point type does not require any DSP resources on the Cisco router.
  D. It can provide G.711 mu-law to G.711 a-law conversion and vice versa.
  E. It can provide packetization conversion for a given codec (for example, if one call leg is using a 20-ms sample size, but the other call leg is using a 30-ms sample size).